Jump to content
SAU Community

Recommended Posts

What temps have people had their M35s up to?

Little worried last night's overheating might have caused problems. It seems fine, and I understand M35s run warmer anyway, just like to put my mind at ease.

I have seen 125 degrees with an airlock in the system, and 116 on the straight at PI. Hopefully no bubbles in your radiator or overflowing coolant reservoir and you should be fine. That said, I am rebuilding another VQ25det atm due to a blown headgasket from overheating...

I finally got the 350 x 400 x 50mm trans cooler in tonight, that should take care of the gearbox temps. I still have to install the fan controller, there is a 9 inch Spal fan on the trans cooler and a 14 inch on the engine oil cooler. Both fans should turn on at a preset temp once I wire it up. Not much room left in front of the radiator now... :)

I finally got the 350 x 400 x 50mm trans cooler in tonight, that should take care of the gearbox temps. I still have to install the fan controller, there is a 9 inch Spal fan on the trans cooler and a 14 inch on the engine oil cooler. Both fans should turn on at a preset temp once I wire it up. Not much room left in front of the radiator now... :)

Pic?

Very reassuring guys, thanks. Sooner I can get the Mishi in the better!

Funny thing about the coolant reservoir. Not sure I've ever seen the level change. Not sure if that is good or bad. Been the same level since I got the car 18 months or so ago.

Pic?

It was pitch black and beginning to rain, with lightning on the way. I was glad to have it finished before the storm hits. Shame there is no room for the hoist in the shed. :(

The trans had the thermostat inline and also ran through the radiator so there was no problem getting it up to temp quickly. I had issues keeping the temps under control though. The fluid comes straight out of the torque converter into the cooler lines, mine was seeing stupid temps as around 30kw is lost as heat in the converter at full noise, quite often enough to boil the coolant in the radiator.

I have removed the radiator fittings and thermostat from the lines so there will definitely be issues getting the temp up now. Hopefully it will still warm enough to drop into 5th fairly quickly, if not I will re-fit the thermostat.

Very reassuring guys, thanks. Sooner I can get the Mishi in the better!

Funny thing about the coolant reservoir. Not sure I've ever seen the level change. Not sure if that is good or bad. Been the same level since I got the car 18 months or so ago.

It will definitely rise once you double the amount of coolant in the system. What pressure cap are you running?

It will definitely rise once you double the amount of coolant in the system. What pressure cap are you running?

The Nismo cap. 1.3... Bar?

Car has never been overheated though, and I've never done anything to the cooling system... Until the cooling mod.

It must have had a large airlock in the system, you need to recheck the coolant when cold for the next few mornings any time you dump it and refill.

I took 2 pics for you guys, the fittings on both coolers are touching the plastic undertray so run the full height of the radiator. Hopefully the Mishimoto will still do its job. This is all possible due to the intercooler being cut down and moved forward, bolted under the intrusion bar.

post-63525-0-67975100-1354276986_thumb.jpg

post-63525-0-62217100-1354277003_thumb.jpg

I also got around to fitting the fan controller for both thermos and for displaying trans/oil temps. Kewish have asked me to modify a few of the signals going back to the TCU, including both temp signals and the main line pressure solenoid. Should be interesting to see what I can do manually with regards to line pressure, and the best part is, no more limp mode if the fluid gets too hot at the track. :)

I need to paint the control panel stealth black yet, if I cbf...

post-63525-0-67777100-1354796321_thumb.jpg

No Navi in the base model... ftw... :)

I can now run full line pressure, (farkin hard shifts), or factory adjustable line pressure with variable adjustment using the TFT temp knobs. Seems to work well on around 60 degrees from my quick play today. It's off to Kewish next Wednesday for pressure readings, I think they will be impressed with the mods. :)

So can i get one thing straight , these air bag like fault/issue lights come on basically due to 'cheap' wiring of sorts ? Or were they connected incorrectly , like the example with the person saying that their battery was going flat and then the airbag light comes on ? :S

Edited by RB25SEB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
×
×
  • Create New...