Jump to content
SAU Community

Recommended Posts

excelent. cos i find on sweeping corners it just frys the rears and the inner front. chopping out tyres real fast. so really if it reduces wheelspin on the track it would pay for itsself in using less tyres :mellow:

excelent. cos i find on sweeping corners it just frys the rears and the inner front. chopping out tyres real fast. so really if it reduces wheelspin on the track it would pay for itsself in using less tyres :mellow:

yes, correct it does help even up tyre wear

when we are launching from a start line, our car use to most times only spin one front wheel, now its all four in a blaze of glory!! :(

russ

Edited by giant
Is there any real advantage to a carbon LSD like ATS make that justifies the difference in price?

well I think the big advantage is you get to tell people you have a carbon diff. but unless they are going to remove your engine and sump and check you can do that anyway and no one will know the difference.

to be honest I don't think it's really necessary. In theory the carbon disks should have some better properties and perhaps they last longer but in reality I don't know how much better (if at all) they are. I've used a carbon clutch and it was great but i'm not tossing my convential clutch in the bin to get one. Cusco diffs are cheap at around $1000 mark and perform very well.

well I think the big advantage is you get to tell people you have a carbon diff. but unless they are going to remove your engine and sump and check you can do that anyway and no one will know the difference.

to be honest I don't think it's really necessary. In theory the carbon disks should have some better properties and perhaps they last longer but in reality I don't know how much better (if at all) they are. I've used a carbon clutch and it was great but i'm not tossing my convential clutch in the bin to get one. Cusco diffs are cheap at around $1000 mark and perform very well.

I thought as much. I had heard carbon clutches need a lot of heat to work well so weren't suited to drag racing. I thought there may be some benefit in that for circuit work but wasn't really sure as I haven't actually heard of anyone using one. Maybe useful for chasing 0.001 seconds a lap when everything else is exhausted but unjustified for everyone else.

I can't really comment on the carbon lsd because I've not used a normal plate front lsd. I've used Kaaz and ATS. The Kaaz rear lsd in the honda is noisy but it's been overtighten. The front ats in the gtr is perfectly quiet after the break in process.

Does your make any noise on reverse Russ and what diff are you using in the rear?

  • 2 weeks later...

Good thread guys - great info.

I busted my front spider gears at the recent Dutton VIC on a launch and turn incident on the long wang @ DECA, so i've got a Nismo 1.5 way front LSD going in this week. The Nismo was slightly better priced than the others and came with gaskets / bearings too where the others didn't seem to.

The Z-tune has the 1.5 way, so I thought it would be ok. I guess i'll be able to give a progress report soon, but.....

I'm told that the ATS 1.5 way front diff was apparently a case of rip the steering wheel from your hand when mounting ripple strips etc, so what we actually intend to do is soften off the 1.5 way Nismo, so that it reacts more like a 1 way. Anyway my thinking was more aimed at replacing the sucker as to increase the strenght over a stock unit, because missing out on 9 events while driving back to melbourne and back again wasn't all that fun.

I'll report back what I think of it on the track when the car comes back.

  • 4 months later...

Be careful when jacking car up to fit front tyres that you dont tighten the wheel nuts up while car is in the air. Locks the front diff up and can result in a car spearing left on 1st launch, and a very dirty racesuit.

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...