Jump to content
SAU Community

Recommended Posts

  • Replies 138
  • Created
  • Last Reply

Top Posters In This Topic

is the response is pretty good? full boost by XXXXrpm?

Good power for low boost to :(

im pretty sure i had full boost by 3500 rpm, but i have to check it out again. was raining last night and i had to drive like a gran.

And thanks :(

well done mate :worship:

my guess was 251.2rwkw

so thats what i wanna see on 16psi...................right !?!?!? :(

and yes, i believe you'll have no problems with the new bov. GFB bovs are very decent.

a gtr bov probably would have done the job too.

Edited by Munkyb0y
well done mate :worship:

my guess was 251.2rwkw

so thats what i wanna see on 16psi...................right !?!?!? :(

and yes, i believe you'll have no problems with the new bov. GFB bovs are very decent.

a gtr bov probably would have done the job too.

im sure i can do it.

and thanks :)

Hey guys finally im ready to finish off my car. really anxious!! Existing mods on my r33 gtst which i made 209rwk

-pfc

-blitz fmic

-ebc

-sliding performance hiflow turbo (non vg30 rear)

-3in turbo back exhaust w hiflow cat

-k@n pod

-stock fuel pump

-stock afm

-stock injectors

-ran 13psi

new mods and retune with these extras

-tomei intank fuel pump

-z32afm

-500cc hiflowed injectors

-hks actuator

-going to run 17psi

what will the final figure be? Take a guess.

Question....who did the highflowing of your injectors???

Depends how happy the dyno is.

I would say between 230 to 250 rwkws....

Whats the prize anyway......do we get to eat the smarties in the jar :)

I won the smarties.... :)

240kws...smack in the middle

quick question guys. i just finished installing the new bov and it keeps stalling when i clutch in as im slowing down in 2nd.

ive tightened it up and it just makes the psssh noise. dosent "flutter" anymore...

did u plumb it back? or leave it atmo?

atmo will give you issues alot of the time. it did on mine to a degree. occasianally stalled, idle was a bit tempremental, and the psshhht gave me the shits.

i plumbed it back, no more problems.

edit: i've got the GFB hybrid bov

Edited by Munkyb0y
did u plumb it back? or leave it atmo?

atmo will give you issues alot of the time. it did on mine to a degree. occasianally stalled, idle was a bit tempremental, and the psshhht gave me the shits.

i plumbed it back, no more problems.

edit: i've got the GFB hybrid bov

i plumbed it back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...