Jump to content
SAU Community

Recommended Posts

i've been meaning to fix up my crappy suspension for a while .. right now its screwed as there are low springs at the front .. i dont' know which ones .. and there are normal ones at the back ... so my choices are either coilovers or springs ... i've had a hard think and i've come to the conclusion that springs are a better choice due to cost ... coilovers = 1k plus camber kit ... so thats about 1.5k when everything is done .. i'd rather spend that money on other things like sound system or mags or even for a rainy day ... what i want to know is ... how many of u guys are running kings on stock shocks?? have u had any problems?? was the handlin much better?? what are the different spring "levels" i can get? will i have camber problems as well??

thanks

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/
Share on other sites

i know this probably isn't relevant cos i dun have an r33 but ive put 1.5in lowered king springs in my hr31 with standard shocks. Im pretty sure they are progressive rate springs and although they have a much higher spring rate than standard, to my surprise they are almost as soft as the originals. got em on special for $250 all round from car toys. They are fine for the moment but you gotta get 4 konis or biltzienz aswell......

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-402834
Share on other sites

My mechanics apprentice has King Springs on standard shocks on his R33 and says it is worse than the standard springs. It handles like a bag of @#$*. I've put Pedders springs on mine and am quite happy with them. I will eventually get new shocks though. The stiffer springs don't quite match the standard shocks properly.

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-402843
Share on other sites

You will find the standard shocks with uprated springs will tend to make the car bounce all over the place as the standard shocks aren't up to the task on dampening the stiffer springs. Thats what mine did, when I added the Bilsteins all round it was a totally different car, handles great now.

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-402952
Share on other sites

hi hip,

i had kings lows (1inch lower) with std shocks, and the handling was without a doubt better than with the std springs. I had none of the bouncing that was mentioned, perhaps my std shocks are in good nick?

either way it will handle better than what youve got now! as ive seen the rake angle your running!

I tried to order superlows, through autobarn mile end, and apparently they dont do them anymore. And anyway, lowering more than an inch is detrimental to handling unless you get coilovers.

even with 1inch lowered i had mild camber problems, the inner rears got eaten out pretty quick (thru lots of launches and wheelspinning tho).

So basically if your going kings, youll be getting the lows (1inch). If you remember last time you sold me the wheels i mentioned i had a set of lows? still have them, 6 months use if that. I will prob sell them if you want, but i need to see how the ride is with the new teins before i do -im back in adelaide next week.

Pm me if your interested dude and we can meet up, prob looking for around 200 bucks? paid 290. Depending on how much time i got, might even be able to fit them for you too.

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-403064
Share on other sites

Originally posted by jlnewton

You will find the standard shocks with uprated springs will tend to make the car bounce all over the place as the standard shocks aren't up to the task on dampening the stiffer springs.  Thats what mine did, when I added the Bilsteins all round it was a totally different car, handles great now.

this what i did, bilsteins with king springs, great combo. to the guy that got the pedders, u got yourself a set of rebadged monroes mate.

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-403778
Share on other sites

I was thinking of getting some King Springs for my R33 too with the standard shockers. I saw some really cheap ones on ebay brand new (actually not sure if they are cheap) $90 for a pair of low (30mm) and super low (50mm). The reason I think it is cheap is because the guy at the tyre shop wanted $380 to get my car lowered with the same springs. So if I buy these and install it myself, will be saving $200 :)

I just hoping that it is easy to put in and handle better and not worse!!!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/19172-king-springs/#findComment-404043
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...