Jump to content
SAU Community

Recommended Posts

spotted bunta on fairfield rd this morning (was in mates corolla, saw you turning off at yeronga, was waving like a madman, mates in car wondered what the heck i was doing)

and then spotted marc in my support room getting a famous xmas pudding, so lucky!

Thank god I'm on holidays, don't have to see you stalking me everyday in the carpark :laugh:

hope this helps dan http://en.wikipedia.org/wiki/Paranoid_schizophrenia :laugh:

spotted a red 32 sedan on loganlea road around 12.30 today ( i may be stalking you too) im not :P

Edited by darren32
spotted bunta on fairfield rd this morning (was in mates corolla, saw you turning off at yeronga, was waving like a madman, mates in car wondered what the heck i was doing)

and then spotted marc in my support room getting a famous xmas pudding, so lucky!

Hell yes, can't wait to try it, I've heard good things :)

Spotted Dave being 'impressed and thankful' later in the day

any spot me on beenleigh road pulled over by the police???

"random licence check and rbt"

bawahahahah

pull the other f**kin leg you stupid coppers.

i drive a import, of course you dipshits will use that excuse with me.

LoL you take them to court, you get the little black cross :)

nothin to do with the court.

i pulled out of my street onto beenleigh road

came up next to them at the lights (they havent even seen my plates yet)

then drove off and they were next to me startin to slow down, pulled in behind me and lights came on.

just did a licence, rego check and rbt.

dipshits didnt look like they knew wat they were doin

took 20mins!

the next check they do that takes that long, i send them a bill for 1hr of wasting my time!

going to say that choyda is stalking me

just assume i spot him once a week =P

Not a very good stalker then are they :P ?? or is it the other way around?? :(

Also saw a black 33 gts25t at mt omaney shops bout 12ish

I spotted Chris in the flesh at chermisde shopping centre yesterday...

Chris as in r33gts4door Chris, we had a nice little chat in JB Hifi... Sorry I had to cut it short buddy, my other half was just keepign track of time... We didnt finish shopping til closing time... :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...