Jump to content
SAU Community

Recommended Posts

Hi all

I have a R34 GTT with the following suspension mods:

- tein super streets

- whiteline front (24mm) and rear sway (20mm) bar both on soft

- front and rear camber kits

- front castor kit

- aligned to SKs settings, pretty much everything is SK spec except coilovers and slightly smaller rear bar

Problem I am having is that when I take say a hard left corner, the rear seems to hop hop hop as if the rear passenger wheel is coming up and off and onto the road again. Its either that or the tyres are rolling on the side so much that Im getting that feeling. it is hard to explain but its like the rear of the car is hopping along to follow the cornering line.

The front seems fine to me and is well planted.

Any ideas what it could be? or what I should try to get rid of it? is it too much body roll?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/193750-rear-seems-to-hop-on-hard-cornering/
Share on other sites

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

Dont quite get what you mean by bucking BB? But im def. not getting on the power early

like as in the car is behaving as though it was a mechanical bull. ie jerking up and down as you are cornering?

I get that, but only on the street. I know my rear springs are too hard, but is there another reason it happens?

I seemed to have that problem at one stage :) my cars left hand rear shock had gone simple bounce test later and a replacement found and its been all good so far

it bounced around on tight corners but also on long sweeping corners at speed :) however it may have no relevance as i have a 33 but still thats my 2 cents hope it helps :)

Edited by SeanO
Were the Teins new?

You keep having weird problems with this car eh.

Are you slowing or accelerating through 80km/h during this corner?

Have you got a new bike yet?

Hahaha i dont really have any problems at all, i always think i do but its always fine in the end, i think its just my fussy self hahah

i think ive been pretty lucky to have everything go well with the car so far (knocks on wood)

teins are new, 1 year old, only done maybe 10 thousand km on them

its like a tight bend, im only doing maybe 50km/hr, maybe its just the nature of the bend, its one of those ones that get tighter as you get into it

naah still trying to sell the white cibby first, then onto a 600cc hopefully

i have exactly the same problem too. Theres a nasty winding road when i got to Bendigo its like a U turn on the middle of the hill and each time i turn it seems the tyres are slipping at the rears. Sort of felt like going into a dip and the car bounce back. I installed the tein read my signiture for specs.

Sounds like, insufficient rebound damping in the shocks to control the spring wind up caused by the rear squat on acceleration. Typical of a poorly matched spring rate and shock valving.

If you have adjustable shocks, try winding them up towards full stiffness. It sometimes helps.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just had this happen to me too.  R32 GTR.   Also broke "just before going out onto the track" - someone up there is looking out for us... Very scary since I was about to do a narrow street course with zero run-off and curbs everywhere. Many people on here upgrading to billet uprights and R35 bearings?   Or buying new OEM knuckles?  I am not keen to replace with another s/h 30 year old fatigued part.
    • Top off with distilled water and see what happens. If you keep losing coolant then you know to start looking.
    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
×
×
  • Create New...