Jump to content
SAU Community

Recommended Posts

Hey all, bought some wheels and need a few fiddly things done. I'm new to owning aftermarket wheels.

Firstly 2 of the tires have screws in them, just wondering how I should go about getting them removed and repaired - i think these tires are tubeless and as I said before Im not too cluey on anything to do with these wheels. Rough price?

Are repaired tires safe to drive on and do high speeds? one of these tires is pretty much brand new and it would be a waste to have to get a whole new tire just becuase of a puncture.

Also looking for a pair of bolt on spacers for the 2 front wheels, anybody have good contacts regarding them?

Cheers in advance!

Lukaz

Link to comment
https://www.sau.com.au/forums/topic/194445-recommended-tire-joint/
Share on other sites

Dont waste your time with these dodgy small tyre joints.. I got screwed around by a few of them, they just feed you a whole bunch of BS on why they are good and not to go anywhere else.. Take a drive to a Bridgestone tyre Center, they are straight foward. know what their on about and have surprisingly competetive prices. and they get the Job done right and quick smart..

depends on your location.

i have had 3 punctures in the same tyre and have taken it to the tyre factory in dandy each time i think it was $20.

they do the job but i would not take my car there for anything complicated, they are also pretty slow.

Protek Tyres in Oakleigh (the Bridgestone tyre centre - just off princes hwy on Ferntree Gully Rd) Next to the Ford dealership and car wash.

Speak to John, say you're from Skylines Australia he'll look after you. :ermm:

I've always gone to Tyrepower, Bob Jane etc... or Cantebury Tyre and Mag Supamart have been helpful.

See if the hole can be plugged/glued & tubed, xtra sealed & peace of mind.

I've only seen one or the other done.

you should always make it very clear that you want whoever is changing the tyres to be VERY careful with your rims and you don't want any freakin apprentices touching your rims.

Caus they ALWAYS leave friggin nicks in your rims because most places really don't care.. most people don't even look at the rims afterwards. So they are rough as all hell.

Good idea to take them when really dirty, then you can see any new scratches.

Of course if they are checking for leaks they'll put them in water but still.

Protek Tyres in Oakleigh (the Bridgestone tyre centre - just off princes hwy on Ferntree Gully Rd) Next to the Ford dealership and car wash.

Speak to John, say you're from Skylines Australia he'll look after you. :wave:

I second that.

John's a great guy, always looks after you as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...