Jump to content
SAU Community

Tomei Pistons

NYTSKY

By NYTSKY,
in Engines & Forced Induction

 Share

Recommended Posts

NYTSKY Grand Master

NYTSKY

Posted
Posted

I just found some Tomei pistons that i might purchase,but before i do i would like to ask some questions:

Its for an RB25DET

These are the specs of the pistons:

Bore: 87.0mm (Will this be big enough? Allowing for the bore to be honed.Or will i need to go 20thou over?)

Pin Dia: 21mm

Recess: Nil

Ring: Standard(I think this means they are not Titanium coated.But are still Tomei rings.)

CHEERS

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
bore size will depend a lot on the condition of your block. have you pulled the motor apart yet? your engine builder will be able to recommend which one to go for.

The motor is not apart yet.

I could only see that the seller only had the 87mm pistons,so i was wondering if this would be big enough,allowing for the bores to be honed.

Stock bore in a RB25DET is 86.5mm isnt it?

So having the 87mm pistons would allow for .5mm to be cleaned up.

or is this a too small of a margin to go off.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3552156
Share on other sites
BLN215 Rookie

BLN215

Posted
Posted
Thats awesome.40thou is heaps i cant see why my builder would want to hone more than that.Motor is in great condition.

It'll depend on the condition of your bores as to how much will need to be bored/honed out of it.You'd be best to have the engine pulled down and inspected and/or machined before you shell out $1300+ for a set of pistons that you dont know if you'll need.

Just the way i'd do it :)

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3554956
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
It'll depend on the condition of your bores as to how much will need to be bored/honed out of it.You'd be best to have the engine pulled down and inspected and/or machined before you shell out $1300+ for a set of pistons that you dont know if you'll need.

Just the way i'd do it :)

Well i want to buy the pistons anyway.I should think 40thou over for the pistons should leave plenty of room for honing.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3554958
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted

The seller only sells the pistons in 87mm.So i think that the 40thou over will cover me incase of poor bores.If my bores are in good condiiton,would an engine builder charge more for the bores to get...Bored?

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555149
Share on other sites
BLN215 Rookie

BLN215

Posted
Posted (edited)
The seller only sells the pistons in 87mm.So i think that the 40thou over will cover me incase of poor bores.If my bores are in good condiiton,would an engine builder charge more for the bores to get...Bored?

If your bores are in good condition then you'll be using an oversize bore you dont need too and wasting perfectly good metal that could be needed down the track.You may only need a 20thou over bore so your using 2 overbores when you dont need too leaving you with less life in the engine block/sleves.

But if your determined to get them go for it,just remember were only trying to help you out here.

Edited by BLN215
Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555158
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

always go for the smallest oversize possible. far better to pull down the engine first, inspect. then buy pistons to suit your new bore size. if there is nothing really wrong with the motor you should be going for 86.5mm bore. .5mm oversize.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555276
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
always go for the smallest oversize possible. far better to pull down the engine first, inspect. then buy pistons to suit your new bore size. if there is nothing really wrong with the motor you should be going for 86.5mm bore. .5mm oversize.

In that case i think it would be a better idea to get the pistons in Oz then.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555283
Share on other sites
fEkuaR Experienced

fEkuaR

Posted
Posted
In that case i think it would be a better idea to get the pistons in Oz then.

Definately a better idea. Your engine would be absolutely stuffed if you NEEDED 40thou oversized pistons. Also if you dont go large oversize now you will be able to use the block again if need be in future re-builds. A block can only be taken so far out.

Link to comment
https://www.sau.com.au/forums/topic/199167-tomei-pistons/#findComment-3555635
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...