Jump to content
SAU Community

Recommended Posts

if bench is weak... do more bench.

also for every push movement, do 2 pull movements.

does not work for wanking

Thanks for that, Yer i hear that you should counter the pushing. Face pulls are a good one apparently

Bench is a little on low side compared to squat (assuming thats below parallel in a rack). Just hit it more often with lower reps and eat. Elbows shouldnt flare out, keep them tucked in.

Yer thats what i didnt check when doing it, was alone also. Will have to get someone to look at me when there next.

Bench is a little on low side compared to squat (assuming thats below parallel in a rack). Just hit it more often with lower reps and eat. Elbows shouldnt flare out, keep them tucked in.

Elbows tucked in for bench? Ideally you want somewhere in between, tucking them in to far uses your tri's to much and is more a power lifting movement then one for building muscle.

I don't even care where my elbows are, unless I have an injury. Your body will have it's own form, different to everyone else's. Tucked in or not, whatever, none of that will stop you from getting strong in bench.

What do your sets and reps normally consist of for bench and how often a week do you do it?

Thanks for that, Yer i hear that you should counter the pushing. Face pulls are a good one apparently

Just stick to BB rows.

I find Pendlay Rows forces me to use good form.

Chins are also good.

Always start each rep by pulling the shoulder blades back first.

Elbows tucked in for bench? Ideally you want somewhere in between, tucking them in to far uses your tri's to much and is more a power lifting movement then one for building muscle.

I generalised my comment too much. By tucked in I don't mean 90 degress to your body or close to your body, somewhere in between like you said, I use about 45 deg. herpa derp on my behalf.

Jealous at all you runners & squatters...

Smashed out my traps today, awesomeness. And going to work on those Bird's-fingers;

might take a while tho! Nap time now, then study :(

I generalised my comment too much. By tucked in I don't mean 90 degress to your body or close to your body, somewhere in between like you said, I use about 45 deg. herpa derp on my behalf.

:cheers:

I can't do bench with a barbell anymore, hurts my shoulders for some reason, have to use dumbells instead, sucks having stronger shoulders then my chest, makes it hard to hit chest correctly :unsure:

how did you come to the conclusion that sore shoulder while benching with barbell = stronger shoulders?

The shoulder is a pretty complex joint/socket.

Lots of shit can go wrong with it and/or smaller muscles be left behind when other parts get stronger.

How strong are you with good form bent over barbell rows?

How is your shoulder mobility?

Pretty common issue with the bench/bro-press . I keep away from trying to bench heavy until my shoulders, back and triceps are ready for it.

As TTT said the shoulder mobility is a killer. If you have built the muscles for a strong shoulder girdle your bench will be stronger than without.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
    • Yes it is ATF. I quote @Duncan "it takes a good synthentic auto trans fluid like Castrol Transmax Z" It's not a diff. It's a transfer case. Totally different thing. Yes, fluid will come out the sender hole. No you do not really need to drain it. Just pull the old, quickly poke the new, clean up and top up. But realistically, you should probably take the opportunity to change it anyway.
    • Hey all. I’m looking on replacing my speed sensor on my R33 GTR. Will the center differential need to be drained, and if so, the center diff uses ATF fluid D? I found information on the transmission, front diff and rear diff. Can’t find a for sure answer for the center diff. Any help will be greatly appreciated.
    • I would tend to agree, especially based on the transfer oil being completely cooked by the sounds of it. I bet it was serviced every 5,000km... Which probably worked out to once every 15,000 real kms...
×
×
  • Create New...