Jump to content
SAU Community

Recommended Posts

Yes your bulging discs are doing a great job of that. Strengthening doesn't fix bad form, correcting with proper technique does. I'm not avoiding any weakness here...the back and core get worked just as much in my method, only less susceptible to injury because it's a stricter movement.

My 2c on this one for what it is worth , from past experience.

You have a point about stabillity, thats why sitting or bending the knees with a relatively lighter weight is a good place to start in terms of 'balance'.

However, once you are over a certain weight (body weight for sure) you basically need to have lots of stabilisation all the way up. So legs to core to shoulder girdle ,even wrists. Each of these should not be troubled and totally up to the task before going crazy. They are supporting muscles so should have more than you need to balance and stabilise as the shoulder press should not be used to target them.

Even if you bend your knees or sit, not enough shoulder stabilisation or core strength will see you get an injury with bigger weight.

However , I think where Ghosty and Husky33 are comming from is; once you are lifting strong across those areas a bodyweight press with locked legs won't trouble you.

In the mean time, best practice is as you said ' slight bend in the knees' or sit down and for the safest plan use a lighter weight if you don't have the confidence to press.bodyweight yet.

Edited by rev210

160 as of tonight! And weighing in at 79.7kg...that's double bodyweight :D

165...somebody stop me! Head started spinning as soon as I locked it out :S

Gotta run out of steam soon; at this rate I'm adding 10kg per week.

Yes your bulging discs are doing a great job of that.

My back injury wasn't caused from MP, it was caused from overzealous DL'ing with bad form, which in my defence, I was fairly new to lifting back then and lacked the experience to know better - some of us just have to learn the hard way unfortunately. Hindsight is a wonderful thing...

Strengthening doesn't fix bad form, correcting with proper technique does.

Generally yes, but also no. Correcting technique doesn't automatically make you strong, you still have to train... and think about what 'form' is for a moment. Correct 'form' is generally the most efficient way to perform a movement or action, that doesn't mean it is automatically safe, for example, if a novice overloads the bar and tries the lift with "good form", injury may still occur because they are weak. On the flip side, doing movements in "bad form" but in a controlled manner to build strength in compromised position/less-efficient movement, aids in strengthening the movement when done in correct form, for example, "good mornings" to assist squats etc.

I'm not avoiding any weakness here...the back and core get worked just as much in my method, only less susceptible to injury because it's a stricter movement.

I disagree. CBF explaining why but as a simple test, try and do your seated press weights standing and tell me which is harder.

I don't do seated press, I do standing behind neck shoulder press...with split legs and knees slightly bent. My back stays strict throughout the whole set and I do 50kg x 10 for 3 sets + 55kg x 6 for 3 sets, so not that light.

I don't do seated press, I do standing behind neck shoulder press...with split legs and knees slightly bent. My back stays strict throughout the whole set and I do 50kg x 10 for 3 sets + 55kg x 6 for 3 sets, so not that light.

that's light

Hey, I probably couldn't do 60kgx10 atm, but i will be the first to admit that it is light. And the only reason it is light is because i don't train it as much as everything else, like yourself, and 99% of people.

It's actually pathetic when you look how much higher my bench is.

I don't do seated press, I do standing behind neck shoulder press...with split legs and knees slightly bent. My back stays strict throughout the whole set and I do 50kg x 10 for 3 sets + 55kg x 6 for 3 sets, so not that light.

it's not light for the conditioning goals you have but, it's really quite light if you are talking a standing press at your weight. Again only relative to people who care to lift heavy as their goal.

I'm sure you could train to do heavier if you wanted to but, you are doing what is best for your goals. You don't need to shovel huge weights on the shoulders without good reasons anyway.

I was the same up until 165kg lol, that was my figurative brick wall. I think my grip failed on 170kg at the same point I couldn't really complete the lift, and have only attempted it once.

Good work Birds, keep dat shit up!

Hey, I probably couldn't do 60kgx10 atm, but i will be the first to admit that it is light. And the only reason it is light is because i don't train it as much as everything else, like yourself, and 99% of people.

It's actually pathetic when you look how much higher my bench is.

it's not light for the conditioning goals you have but, it's really quite light if you are talking a standing press at your weight. Again only relative to people who care to lift heavy as their goal.

I'm sure you could train to do heavier if you wanted to but, you are doing what is best for your goals. You don't need to shovel huge weights on the shoulders without good reasons anyway.

It's not light in that the potential for injury is very much there should you use bad form, which is why I brought up what I lift for that exercise in the first place. It's like a 100kg deadlift - nothing in the scheme of lifting and what people are capable of, but you can still do a lot of damage if your form is out.

I was the same up until 165kg lol, that was my figurative brick wall. I think my grip failed on 170kg at the same point I couldn't really complete the lift, and have only attempted it once.

Good work Birds, keep dat shit up!

For someone with a spinal injury, that's a great lift! My grip felt like it had more in it, but 165kg was the first time my back had to put in a lot of effort to get the weight up / started running out of steam. Grip seems to be fine for 1RM stuff, it's the sets of 10 where sweat builds up and resetting my reps turns it to shit, even with much lower weights.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...