Jump to content
SAU Community

Recommended Posts

underhand grip doing rows puts the wrists in a bent back position.

and using a straight bar means they are bent back and twisted out. Then from there they get pulled upwards by the arms, and downwards by gravity.

Use double overhand grip.

either thumb under or over to see what works best.

cheers, makes sense as to what the issue could be.

Bought commercial cable cross over for $100, a second corner cross over unit for a friend of mine for $180, laying down back row for $90, commercial peck deck for $20 (that's right, $20) and a commercial ab crunch machine for a friend for $20. If I had more space, or had known that it was going to be that cheap, would have organised some storage space and bought a lot more. couldn't believe the prices. will post pics tomorrow once I have it either in the work bay or hopefully at home. the $100 is missing the cables that go with it, so will have to source them somewhere, but that's easy enough.

Having seen your dumbell racks I'm guessing you'll be charging membership fees for your garage soon...

I wish I had seen this auction before I bought all my gear. Would have saved thousands

Full commercial power rack went for $180. It was ridiculous.

Worst marketed auction ever. I only saw it on gumtree and decided to pop in see what was there. There were about 30 people there, and they were all looking to privately buy equipment for their homes.

A lot of the gear was very badly presented as well, covered in dust and some of it in mould, with scratches here and there, but it was still fully functional.

I will post pics by end of the week once I get it all home and cleaned up and assembled.

I think I get away with no wrist issues due to using bitch gloves that wrap around and support the wrist a little.

Just buy a proper pair of wrist wraps from the likes of Inzer or Titan and wrap them properly before a set.

If there is still pain you might need some fascia release or treatment on the muscles or tendons.

IMG_1631.jpg

finally, a pic appears.

going to have to move the tv cabinet thingy and fan out and put the pec dec there and will wall mount the tv above the dumbbell rack.

have sold the calgym chest press, and am now already a few hundred ahead of what I paid for all the gear. wish I had bought more....

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...