Jump to content
SAU Community

Recommended Posts

It's been a while since I've been here, how's everyone doing? I almost hit 300lbs bench press but my right shoulder decided to impinge itself :angry: . Have to lighten the load on my favorite workouts, bench press, weighted dip and inclined bench press. Dumbbells press inclined and flat are okay though, I can go heavy as my shoulders have more free range of motion.

275 lbs. Nearly 300 after a generous round up, just like dick measurement hahaha. Now I am down to 220lbs. The gym I go to has a 300 club, where as you guessed, 300lbs bench press guys are members. Would be nice to be in that club.

Be very careful with your shoulders, I was frustrated and disappointed for months man, and the sharp, teary-eyed pain of just waving at a person made it even more depressing. I was told that might need surgery but only an MRI and a ortho can make that assessment. My right shoulder is miles better and I am slowly building up, using more dumbbells and other workout until I can get my shoulder to agree with what I need to do in the gym.

Supplements, whey protein, multi-vitamins, fish oil, and tribulus. Diet, lots of fish, few carbs, and as much vegetables as I can get. No sugars and sweets, but I don't skip eggs and bacon, and the occasional junk foods like pizza and big burgers :)

Mondays: Squats and dumbbell press, inclined sit ups at 10 reps 3 sets.

Wednesdays: Weighted pull-ups, dumbbell rows.

Fridays: Squats and inclined dumbbell press, inclined sit ups at 10 reps 3 sets.

My simple workout consists of those on Mon, Wed, and Fri, at 5 reps and 5 sets. Mixing a few workouts in between like inverted rows and punching bag.

  • Like 1

Good question. I do deadlifts, but in between the core workouts, mostly dumbbell deadlifts and I don't go heavy, 170lbs combined weight. What's your workout now Birds? I remember you had a nice, well thought out program, this was like years ago on SAU.

You're probably talking about my workout of old which was a bit of a bodybuilder workout. I think it was a good workout that gave comprehensive coverage of the body, but excessive exercise and time in the gym for what I needed.

After a bad shoulder injury during incline bench press (resultant from boxing and heavy weights) I was forced to rehab and re-introduce one exercise at a time or risk re-injuring and doing no gym at all. It was this process that overcame the OCD I had, not wanting to give up any of the exercises I had been doing and spending 4 times a week in the gym for 1.5 hours a pop, sometimes 2.

Started with squats cause least shoulder involvement. Few weeks later introduced deadlifts as it didn't put a lot of strain on my shoulder either. Having been a couple months since the injury with no upper body exercise, my upper body was losing a fair bit of muscle mass, so a few weeks after introducing deadlifts I give neutral grip pullups a go and found that they didn't aggravate the shoulder too much, just a little soreness. 6 months after the shoulder injury I thought I would give the bench press motion a go - grabbed a 15kg barbell and started pressing very carefully and slowly with a strict powerlifter form that I had not used before and closer grip to protect the shoulders. Also brought the bar right down to the chest and all the way to near lock out. One advantage to injury is the forced opportunity to reset form like this and take solstice from having great form (a great excuse for being weaker in the exercise, as we often don't want to accept the realities of injury making us weak).

The range of motion was a tiny bit tender and I didn't have full flexibility in the right shoulder, but I repeated this process for a couple weeks and it gradually returned. Each bench session I would push it that little bit harder striking the fine line between hurting myself and forcing the injured tissue to re-injure and heal around the movement. When that started feeling good I very progressively added weight, moving up to 20kg bar and then 22.5kg etc. All the way up until where I am now about 2 years later. Shoulder still isn't 100%, it never will be and I'll always have a little pain...but you know what, with new and better form and a gradual build up I made my PB of 127.5kg (280 pounds) a couple months ago; a competition style lift. My old PB pre-injury was 120kg and not touching the chest. So you can come back from those injuries you just need to give the body time and respect to do it's thing, be patient and gently work it through the motions until it's ready.

Forgot to mention...after introducing those four exercises, the DOMS I experienced all over my body made me realise just how much of the body was being worked by those exercises alone. I decided to stick with those because they weren't hurting the shoulder much and before I knew it it had returned to the weights I was lifting before and even making new PBs - lead me to wondering why I bothered with all the other assistance exercises in the past.

Which is why my current workout looks like this: deadlifts, bench, squats, pull-ups - two of these on one day and two on another. 45 minutes in the gym 2-3 times a week and I'm bigger and stronger than ever.

You're right on with working out with an injury. I do more varied workouts and work around my shoulder, focusing even more on form too. I have more weak areas than I thought when I use slow proper form. Man, it was a depressing months of pain for me, but now I am slowly coming back. That feeling of progress is just as good for me as hitting my PB.

How I got my injury? Lifting my mom's potted plants. These guys are heavy, and most have rooted to the ground. Worst of all, they are thorny so I had to hold the pots straight out in front of me. Get up the next day, and I couldn't even raise my hand to wipe the cheese in my eyes.

speaking of injuries, anyone have any recommendations what to do with a groin strain? not sure where or what it's from but most likely deep or heavy squats

i'm thinking resting and stretching and some cardio for a few weeks while i recover

Stretching helps. Accupuncture helped when i did my groin and i could barely walk.

I have found since jumping on the bike before legs i have less issues. Also compression pants during oztag have made an amazing difference

275 lbs. Nearly 300 after a generous round up, just like dick measurement hahaha. Now I am down to 220lbs. The gym I go to has a 300 club, where as you guessed, 300lbs bench press guys are members. Would be nice to be in that club.

Be very careful with your shoulders, I was frustrated and disappointed for months man, and the sharp, teary-eyed pain of just waving at a person made it even more depressing. I was told that might need surgery but only an MRI and a ortho can make that assessment. My right shoulder is miles better and I am slowly building up, using more dumbbells and other workout until I can get my shoulder to agree with what I need to do in the gym.

Bro press done without supporting movements for the shoulder girdle is a path to pain and girly lifts . People wind up with imbalanced muscle strength.Then cop a rotator issue. The internal rotaion favorites like bro-press and even bro-cep curls pull the shoulder forward and shorten the muscle range of motion (without counter balancing movements).

My tip for you if it helps ( having had that issue before).

1)You need to quit doing anything lift wise that is focused on internal rotation (bench / shoulder press etc) Save for simple activation and range of motion of internal rotation movements.

2)Rehab properly (as you probably are)

3)Build a cast iron upper back and scapular / shoulder girdle with good mobility. It's the platform to your strength.

4)Then slowly get back into the shoulder press and after some time, you can go bro press.

Supplements, whey protein, multi-vitamins, fish oil, and tribulus.

tribulus does nothing. If it did , it would be a banned substance. Save your money dude.

Hope your shoulder gets well soon mate.

Edited by rev210

by the way , rotator cuff is a potentially degenerative injury. The pain is also refered (you will feel it in all sorts of places other than the back of the shoulder) , so movements can feel fine when you do them but, increase the injury further.

Doing dumbell presses etc. when you can't wave hello is not a good idea for example . It could micro tear the injury further.

by the way , rotator cuff is a potentially degenerative injury. The pain is also refered (you will feel it in all sorts of places other than the back of the shoulder) , so movements can feel fine when you do them but, increase the injury further.

Doing dumbell presses etc. when you can't wave hello is not a good idea for example . It could micro tear the injury further.

Thanks rev210, it is good to hear tips from people who've had similar injuries.

My shoulder's much better now, bench press gives a small degree of a pain, and much less with dumbbell presses. I am thinking it could be that the dumbbell press frees up my shoulder a bit more than the bench press. I wish there was a sport scientist or doctor I could speak to about, but there are non on this island. Reading your post got me thinking and am a bit concerned, I don't want it to get worse. I'll try out your suggestion and Bird's as well.

For the tribulus, well, it kind of helps I think. Mentally? Physically? Spiritually? Well I've already paid for it so might as well finish the bottle :(

No probs.

If you used to bench press with no pain then having any pain shoulder be a concern. Fix the shoulders properly and you will have none. No need to push through things in this case.

There are lots of youtube vids now to help you check the mobility of the shoulders , rehab movements and strength builders. have watch of a few and try things out.

Ultrasound would be first point for me, just to get an idea if anything is inflamed

How long have you had it for?

Anything you can narrow it down to that might have caused it?

Does it come and go or is it there all the time?

Only certain exercises activate the pain?

Sorry for the late reply Birds,

I had my elbows checked out by my physio last week, and she said it appears to be that the tendons are inflamed and it's a bit of an odd case in the fact that it isn't narrowed down to either tennis elbow nor golfer's elbow. I've been advised to stop stretching my triceps (overhead tri stretch) for the time being as that just aggravates and pulls on the tendons further, and also to carry out to isometric contraction holds (elbows at 90, push against solid surface as hard as possible with no pain for 10sec then 30sec rest x 5 reps) a few times per day for now to see how it reacts.

Now in response to some of your questions, I've had the issue for quite some time now although it has gotten worse the heavier I lift. When I did a 50kg DB floor press the other day it really seemed to disagree with that movement and it has been sore ever since.

The worst exercises that will definitely cause that pain seem to be anything that puts the triceps in a stretched state, so that's why skull crushers and overhead tri extensions are out of the question; they have been for some time now to say the truth.

I'm avoiding presses for now while it settles a little, but then the physio has advised my to start performing heavy triceps pushdowns as the elbows and tendons seem to prefer this type of movement for strengthening as it allows blood flow into an otherwise quite restricted area.

Is there an band work you can do to rehab the joint and work the injury through a range of motion with minor resistance?

Think it's time to take a rest from the heavy weights and take the rehab seriously

Focus on legs; that's one advantage to an upper body injury

Avoiding too many ROM based rehab exercises as apparently the best type of rehab for it is the iso stuff right now until I can do that comfortably without pain.

So yes, time to back off on heavy presses and take the rehab very seriously, today's session had no pressing to target the chest, rather just a pec fly.

Currently hitting legs 2-3x per week depending on how many sprint sessions I do as well (aiming for 2 per week). Hopefully it all comes together nicely and I can get back to the presses before long.

Appreciate your suggestions

It's been a while since I've been here, how's everyone doing? I almost hit 300lbs bench press but my right shoulder decided to impinge itself :angry: . Have to lighten the load on my favorite workouts, bench press, weighted dip and inclined bench press. Dumbbells press inclined and flat are okay though, I can go heavy as my shoulders have more free range of motion.

Hit 352 8weeks ago, put on about 5kg of size over last 12months so my levers are far better, plus whatever muscle for strength too.

That's badass jangles. Man, I was (kinda) close to 300 a while back ago and now am working my way up again. I am to see an ortho this 24th so I hope to get some answers for my right shoulder. I want that 300, dammit.

Hit 352 8weeks ago, put on about 5kg of size over last 12months so my levers are far better, plus whatever muscle for strength too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...