Jump to content
SAU Community

New Gt-r Designed For Americans, Not Japanese?

funkymonkey

By funkymonkey,
in R35 GTR

 Share

Recommended Posts

funkymonkey Grand Master

funkymonkey

Posted
Posted

A mate that just got back from japan commented that there's been a small stumbling block to the R35's sold in japan. In japan when you go to register your car, one of the things you have to provide is you shako shoumei details. ie. your parking space allocation. Now to those living in rural areas, or with their own garages this can be whatever size they deem fit, but if you live in the city and lease a parking space from the city, then the size allocations are preset. Most of these spaces are under the width of the R35, which means that some potential buyers in the big cities cannot own the car, or must go to great difficulty to own one. To date most japanese cars are designed with the average parking space size in mind, but Nissan's kinda gone "f**k it" with the new GT-R.

From memory the last japanese car that was designed like this was the NSX, and that again was designed with the US market in mind. If you look at porka's, audi's and other mass produced european sports cars (ie not ferrari's n lambo's), their wheelbase is narrower than the new GT-R. I suppose having a small narrow car like the older GTR's sitting next to a Charger, Corvette or Rustang would look kinda small and girly. So besides the advantage of a wider track, was the design of the R35 to comfortably seat the McDonalds fuelled wide asses of yanks?

gtr.jpg

typevu Grand Master

typevu

Posted
Posted (edited)

HEY if you read the whole story the ugly ducking turns out to be the hottest piece of ass out of em all! Sooooo the R33 is that hot piece of ass :ermm:

Edited by vietorious

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...