Jump to content
SAU Community

Recommended Posts

Hi,

I have a Stock R34 GT-R and I put 20L of Caltex Vortex Premium by accident (which has a octane rating of 95) when I should have filled with Vortex Premium 98. This happened because there was no Shell V-Power left at the Shell servo so I decided to use Caltex for the first time and I thought Vortex Premuim was their 98 octane rating fuel.

So my question is this, do I have to empty the fuel tank of all the current fuel ASAP to avoid damage or can I get away with using this fuel (not driving hard) until it runs out and then fill up with the 98 octane rating fuel.

Thanks,

Glen

Link to comment
https://www.sau.com.au/forums/topic/205557-fuel-for-r34-gt-r/
Share on other sites

with the std ecu it has maps based on 98 RON fuel

now that the user has put in penis fuel (95 ron) the timing will be too advanced so it will combust without spark - detonate / knock

this in turn will tell the ECU its knocking (assuming stock ecu) and the ECU will drop the low octane map

its still bad for the engine and i wouldnt load it up on purpose with penis fuel in it

the stock ECU has no idea (or any ecu for that matter) what octane fuel is being used

all it does is watch the knock sensors for detonation, once it seems certain levels of detonation

it assumes penis fuel is in use and drops back to low octane maps, which basically have retarded timing on them

this makes the car not detonate as the timing is very relaxed and makes the car doughy and flat

yes so in summary

your options now that you have put penis fuel in the tank

1) drain the tank and put high octane in it

2) baby it around and then put high octane in once empty

3) use octane booster and baby it around a little - i would still avoid full loading it up

it will never detonate on light cruise / crusing at 100kmh in 5th or 6th

if its going to detonate with penis fuel, it will be when its ramping on boost or on full load

this is because the engine is under load, and has much more aggressive timing

I wouldn't use octane boost .. I'd rather not have that in my motor after seeing the dirty stains it left through my last GTR's head. Maybe its just cosmetic but even so.

The 34 GTR stock ECU will probably pull timing on you even when you are driving around normally. When I had even a slightly bad batch of 98 in my 34 it would pull timing quickly after driving for a little while and would leave it retarded until you switched the car off and back on. This happened more than once so i correlated the occasions to a particular servo and avoided that from then on.

Don't load it up and fill the tank with better fuel when you can next.

if u want to use octane booster...why not use snake oil, it will have better effects :P

http://au.youtube.com/watch?v=2jbcCr2ll3c

octane boosters do shit all. put that money into an extra 5ltrs of 98 :)

I dont know what you guys are talkin' bout. has anyone actually done it and had problems???? I assume it would if you are running a massive setup, but for basically stock applications it is fine. I have done it to trial different things to my car (I didn't drive it any different - still flogging the guts thru it) and it did nothing... Think... Its 3 octane different out of 95-98.

Don't be worried mate, if you want to be careful, just don't flog it too much. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...