Jump to content
SAU Community

Recommended Posts

Spotted KB33 about 2:30pm today on Port Wakefield heading North then turning right at the BP... I was on the otherside of the road honked at ya but you looked at the rear view mirror instead lol

lol.. i so that was u VU!! didnt notice u lol

I was at windys last night with 6x r33, 2x r32, 2x S15 & 2 34's one 4door the other 2. Nothing overly exciting though everything looked rather stocko :thumbsdown: but everyone had a good time so was chill

'sniper' was there too, i think it was a mini NS cruse...

Edited by Volk34
seen sled cut a lap of jetty rd on the bike this morning

ahh didn't see you, did you toot?

Cibo's coffee at the Bay in the morning is the best.......putting up with Pete Motley's jokes at that hour every morning is not so good.

spotted matty in the mud hunter with the 31 on a trailer turning right off NE road onto wright road... love those wheels on the 31... what are they? was in a mates Sti so didnt beep

then a purple 33 GTR on the side of the road on Sudholz rd.. hope everything is ok

ahh didn't see you, did you toot?

Cibo's coffee at the Bay in the morning is the best.......putting up with Pete Motley's jokes at that hour every morning is not so good.

nah,i was sitting at gloria jeans coffee shop.little boy was restless this morning so took him for a spin in the pusher

spotted matty 31 in the MUD HUNTER on lonsdale hiway last night near hallet cove

must not hav seen ya mate, was in my own world last nite lol

spotted matty in the mud hunter with the 31 on a trailer turning right off NE road onto wright road... love those wheels on the 31... what are they? was in a mates Sti so didnt beep

think they're sparcos mate, that was craig r33's skid car on my trailer, taking it up to Garage 7 in Mt Barker.

Spotted Jasmin at her work as Craig and i filled up just after that (hiiiii jas :P)

and to all the douches that think im "just towing a trailer" and can cut in on me, f**k you. i will f**king drive over the top of you if you want to push your luck

/rant

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...