Jump to content
SAU Community

So I Cut My Bonnet Release Cable On My R34....

SS8_Gohan
 Share

Recommended Posts

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

As per the title, long story short, i cut the cable that runs from the cabin to the bonnet latch.

Quick question, does this make the bonnet more susceptible to flying open at high speeds and smashing my windscreen??

adam-__- Grand Master

adam-__-

Posted
Posted
"oh sorry officer, the bonnet doesn't seem to be opening!.... i guess you can't inspect my engine bay :)"

*** slaps a defect sticker on window for not being able to open bonnet ***

skymugs Collaborator

skymugs

Posted
Posted
*** slaps a defect sticker on window for not being able to open bonnet ***

actually it worked for me.. i broke the plastic on the latch and it couldnd be opened unless u had pleirs( pain in the arse though)

it was a big defect staton set up at the airport.. i got off without them even checking my hight or exhaust noise, both illegal :(

my 2 mates got fines

adam-__- Grand Master

adam-__-

Posted
Posted
so has the original thread poster come back in here and tell us WHY he cut the cable?

He just felt bored. hahaha :O

I would assume that he cut it because he thought it was a cable tie or some speaker wiring. I've seen someone cut an important cable because they thought it was a cable tie. :(

SS8_Gohan Grand Master

SS8_Gohan

Posted
  • Author
Posted

jeebus, forgot about this thread!!

ok, story...

left keys in ignition... drains battery (not sure how, no lights were on) but not completely. Alarm remote still functions, car is arming and disarming (according to the icon on the remote) but not enough power to actually open the door locks.

Ring RACV. They come out, try initially to wedge the window open a bit where the it meets the soft rubber strip, so as to get a wire in to pull open door luck. Not much give in the window, RACV guy concerned window will shatter.

Puts wedge in between window and door rubber strip (horizontal bit) to try and get the door lock rod (horizontal). Manages to get the rod and door lock starts to come open. BUT even though there wasn't enough power to open the central locking, there was apparently enough power to KEEP the solenoid working and not allow the RACV guy to actually open the lock. Highly annoying.

Keeps trying for 30mins+, different wires etc... I then say, if we can get to the battery, perhaps if we jump it, it will solve our central locking problem. So i try pulling on the bonnet cable by reaching from underneath the front bumper. Get the latch to move about 1mm, but Nissan have thought of this, and the wire that does the opening is on the inside of a plastic covering so pulling on it does jack shit.

I then ask, can we cut the bonnet cable? Discussion ensued about relative pro's and con's and prices of getting locksmiths out. Decide to cut the bonnet wire.

EASIER F*CKING SAID THAN DONE!!! It is one tough mofo of a wire to cut, especially when i have a street sweeper spec front bumper, it was hard to get to and then it took both our efforts to cut the f*cker (the wire that actually does anything is encased in strands of steel cable!!) Eventually cut our way through and the latch pops open!! yipee!!

Pop bonnet, jump battery, alarm starts working again, opens the central locking and away i go.

$60 for bonnet cable from Nisswreck in SA, but has yet to be installed. Anyone know if it will be a shitter of a job?

/end story

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...