Jump to content
SAU Community

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

i'd guess to them any kind of wheel spin would be considered as "hooning" "burnout" etc

having said that, i do think some cops are considerate at times.

once at the lights on a very wet day, on the tram tracks and right next to me at the lights was a marked cop car. i took off and rears starting spinning (not intended ofcourse) the cop just looked at me and drove off... on a different day/different copper and i woulda probably got done for it

you cant generalise on anything these days...

i'd guess to them any kind of wheel spin would be considered as "hooning" "burnout" etc

having said that, i do think some cops are considerate at times.

once at the lights on a very wet day, on the tram tracks and right next to me at the lights was a marked cop car. i took off and rears starting spinning (not intended ofcourse) the cop just looked at me and drove off... on a different day/different copper and i woulda probably got done for it

you cant generalise on anything these days...

you bloody hoon rimon

^^ i was wandering that too if i launch at saw 3500rpm and dump the clutch but dont go over the speed limit.. is there any law i'd be breaking?

if you dumped the clutch at 3500rpm and didn't spin your wheels the cop would probably just laugh at your car :)

if you dumped the clutch at 3500rpm and didn't spin your wheels the cop would probably just laugh at your car :)

lol i didnt mean without wheelspin but can they get u for a bit of wheel spin on launch? its not like doing a burnout or nothing its RWD so its bound to happen..

lol i didnt mean without wheelspin but can they get u for a bit of wheel spin on launch? its not like doing a burnout or nothing its RWD so its bound to happen..

Yes they can get you for spinning the wheels.

And its not bound to happen unless you don't know how to drive.

Just ring the EPA and report there car as a noisy/smokey vehcile.

Pretty sure they are not exempt from Environmental Laws.

Pity its illegal to make false reports :)

Anyhow as justin said in the wasteland, whats the point of this thread overall?

You shouldnt street race... so "race or not race" isnt even something to be considered...

Even if you dont wheel spin, if you are going flat out in each gear up to the speed limit, the change from first to second will most likely make your car wobble at the rear. And if the cops are trying to egt you, they will probably pick on you for that. There isnt much point to red-lining through first before having to slow down in second.

Damn, i hate the police even more now. I've only encountered few decent officer in my life and the rest just seemed to be arrogant assholes, carrying a head up the ass attitude.. Hate to generalize but can't avoid it at times, so its better to avoid them at all costs...

I bet they have a similar opinion of import drivers. It's a pity there are so many dick head import drivers out there, makes the rest of us look bad.

BTW is the Black tinit on the unmarked VE's legal?

Seriously I have seen people defected for the same!

Lawful exemption once their in uniform? :nyaanyaa:

Also about the launching from the lights crap, I wouldn't try it because the popo could still get you for "Engaging in a race or speed trial". Taken from http://www.dpc.vic.gov.au/domino/Web_Notes...33;OpenDocument

They also used to have something about "unnecessary exhibition of acceleration".

"Engaging in a race or speed trial".

They also used to have something about "unnecessary exhibition of acceleration".

LMAO. If they dont like you they have something they can get you with some way or another.

you weren't the blue 34 gtr with gold rims that was 'accelerating fast' against a black gallardo a few weeks back on blackburn road are you?

haha busted.... :laughing-smiley-014:

I would of revved too, then moved up a little closer then revved and revved some more....light's about to go green, reaaaady....take of at 2km an hour. Gold!

lol i do this to ppl in commonwhores who try to race

its funny :thumbsup:

the unnecessary acceleration law states that it is up to OFFICER DISCRETION as to whether you were breaking said law... the same is for breaking traction... all you would need is the tiniest noise (which aint hard with FAT tyres :thumbsup:)

also it is illegal to swear directly at an officer, or make an obscene guesture towards one... i'm sure a few of you will remember the debacle a few years ago when that guy stuck his finger up at a speed camera (when they were run by cops) and got snapped and niel mitchel (i think) paid the $1000 fine for him... then the cops kicked up a fuss but there was technically no law against "gifting" $1k and him paying the fine....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...