Jump to content
SAU Community

Recommended Posts

The GT3076R when I looked for and chose one looked like it'd be best used at around 22psi on a built RB25DET so there isn't a huge amount of use for it over that. Its a nice not overly laggy turbo on an RB25 so with 22psi there should be a huge fat power delivery, it'll be wicked for a road car that can do drag and track. Just because the engine CAN make 100hp/cyl doesn't mean you are obliged to - it just adds one part of the equation to get what you want out of it.

Highest power pump gas/power per litre car I've been in was a still 2litre EVO 2 running a .82a/r GT3582R running ~2bar of boost putting down just under 500whp (125whp/cyl), way faster than any daily driveable 4cyl street car should be.

Yeah i agree with you about having a drivable car and not necessarily having to run at the 100hp per cylinder mark. I figure most car enthusiests that do get to own a car that is stupidly over powered proably in the end gets rid of it and trades down to something with a more practical power range.

Personally i hate big turbo cars. Lag, followed by the lack of traction that follows. A problem caused by running a turbo so big that its flow is in the middle of its efficency range when the engine is at its redline. I much prefer having a car thats matched so that in the middle of its rev range, the turbo's are pumping at the middle of their efficency range as well.

And dam! 500rwhp in an evo! Those poor tyres... :D

Personally i hate big turbo cars. Lag, followed by the lack of traction that follows. A problem caused by running a turbo so big that its flow is in the middle of its efficency range when the engine is at its redline. I much prefer having a car thats matched so that in the middle of its rev range, the turbo's are pumping at the middle of their efficency range as well.

And dam! 500rwhp in an evo! Those poor tyres... :D

AWHP EVO, not rwhp haha - and it put its power down extremely well, its an absolute monster on a race track.

I don't mind big turbos, they have their place - I just hate it when people under or oversize their turbo for their setup. For example, that evo running 280degree cams and revving to >8000rpm on 29psi is running not overly short of the choke line of the compressor map at redline but it is a huge turbo on a small motor. On the other hand I reckon a lot of people on SAU using GT-RS are running them beyond their efficiency (both hot and cold side) and I'd hate to imagine what life would be in the exhaust manifold of those things.

Anyway, sorry to thread jack Nytsky - I find it hard to avoid this thread as I am amping to see how your car goes, when do you expect it to hit the dyno? :down:

(edit after seeing Cube's response) Yes, you hurry up too ;) I eagerly await both of your results and impression to help decide the fate of mine haha

Edited by Lithium
Yeah i agree with you about having a drivable car and not necessarily having to run at the 100hp per cylinder mark. I figure most car enthusiests that do get to own a car that is stupidly over powered proably in the end gets rid of it and trades down to something with a more practical power range.

Personally i hate big turbo cars. Lag, followed by the lack of traction that follows. A problem caused by running a turbo so big that its flow is in the middle of its efficency range when the engine is at its redline. I much prefer having a car thats matched so that in the middle of its rev range, the turbo's are pumping at the middle of their efficency range as well.

And dam! 500rwhp in an evo! Those poor tyres... :D

I ran a GT3076R .82 on my stock RB25 for 18 months, it was nice once you were moving, 1st gear and most of second was a nightmare because the turbo just hit so hard it would just wheel spin all over the place, even in 3rd it was a hand full coming into boost because of how hard it hit, more like a light switch, I then switched to a GT35R .82 and it was far better, much easier and more fun to drive, I can change gears at 5000rpm in 2nd into 3rd and stay at 1bar (my low boost), My customers RB25 is running a T04z and I personaly find that even easier to drive on the street in lower boost levels than the GT35 purely because its much smoother and more progressive coming into boost and having a 4000rpm band of 1.5bar makes it just as easy to drive as my GT35R (besides that it KILLS me in a straight line) I also find around a track that big turbo is also a lot easier to drive because you can give it a lot more pedal in and coming out of a corner and you can feel it starting to power up vs the smaller turbo's where they just hit and your left going sideways.

Just my 2c on why somtimes larger turbo's can actualy make it easier to drive.

lol you sooks

I run a GT3076 with a 0.63 rear, and it makes 314rwkw, and 720nm of torque.

Drives like a V8. Curve was exactly the same as my mates 300rwkw LS1, except he had a bit more torque under 3,000rpm.

I wish mine was like that, I would get to 3300rpm odd and BANG 1.5bar, tire smoke and drama, probably why I only managed an 11.6 with that turbo, the pull away was a nightmare almost always a 2.1 or 2.2 60ft. I think with the weight of your R33 vs my S14 also would make it a lot more noticible for me, I am now doing 1.8's and 1.9's with the GT35, high 10 here we come.

if its that bad maybe try a good boost controller, i know my avcr is able to be programmed for each gear and in 1000rpm increments, using one of those will get you the full power of the 3076 up top but more controllable down low.

I wish mine was like that, I would get to 3300rpm odd and BANG 1.5bar, tire smoke and drama, probably why I only managed an 11.6 with that turbo, the pull away was a nightmare almost always a 2.1 or 2.2 60ft. I think with the weight of your R33 vs my S14 also would make it a lot more noticible for me, I am now doing 1.8's and 1.9's with the GT35, high 10 here we come.

Maybe it was the setup? Were you running an aftermarket exhaust manifold?

I run the GT3076r .82 IW on the RB30DET. That pretty much makes a psi straight off idle then ~5psi at 2000rpm; 9psi at 2500rpm and then 19psi odd at 3100rpm.

Boost is fairly tractable with simply less throttle input; or I just grab the next gear and let the torque lug it out. :ermm:

Yeah it was an aftermarket top mount with 38mm tial, could happily run .8bar, but even with .8 it hit had with the Profec b set to zero everything low boost it would hit hard and would try to come in very fast around a track, then again my "coming in hard" could be different to your coming in hard, I stuck that turbo on an SR20 and it was a joy, came in beautifuly! even ran faster than me at the same boost :-(

Anyway, sorry to thread jack Nytsky - I find it hard to avoid this thread as I am amping to see how your car goes, when do you expect it to hit the dyno? :ermm:

(edit after seeing Cube's response) Yes, you hurry up too :) I eagerly await both of your results and impression to help decide the fate of mine haha

Will be going to the exhaust shop in a week or two,then its off to the tuners so it will be on the road in a month id say.

On a side note my throttle cable is now too short for the plenum and trottle adaptor.No matter how i run it,it wont work.There must be people running the same setup as me who have got around this problem. Any suggestions??

Will be going to the exhaust shop in a week or two,then its off to the tuners so it will be on the road in a month id say.

On a side note my throttle cable is now too short for the plenum and trottle adaptor.No matter how i run it,it wont work.There must be people running the same setup as me who have got around this problem. Any suggestions??

Z32 throttle cable

did you have to roll the gaurds to get the rears to clear?

what size tyres do you run?

Nope,did not roll the guards.The offset in the rear is +42,and 265 wide tyres. The tyre sits about 10mm away from the coilover.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...