Jump to content
SAU Community

Crank Strength And Upgrading Options.

LedZepLen

By LedZepLen,
in Engines & Forced Induction

 Share

Recommended Posts

  • 3 weeks later...
  • Replies 213
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

nismomiles33
nismomiles33

I used a grub screwed, machined and balanced, nitrated standard crankshaft (Nizpro spec??) .. should hold up with most, I was told that should be good for 800+HP.

Posted Images

R.I.P.S NZ Collaborator

R.I.P.S NZ

Posted
Posted
really where did you see that?

We've already finished the worlds first genuine RB33 (ie actually slightly over 3300cc) and it was not quite as simple as we first thought it would be, we have twin 3037s and it will be shipped to Ireland for install in a R33 GTR shortly.

I can also vouch for stock RB30 cranks to 9000rpm 1000+hp, and stock RB30, pistons and rods to 8000rpm and over 500rwkw in a track car without problems, although I usually tell my customers 7200rpm, 1.5 bar 400rwkw.

Rob

FineLine Grand Master

FineLine

Posted
Posted
We've already finished the worlds first genuine RB33 (ie actually slightly over 3300cc) and it was not quite as simple as we first thought it would be, we have twin 3037s and it will be shipped to Ireland for install in a R33 GTR shortly.

I can also vouch for stock RB30 cranks to 9000rpm 1000+hp, and stock RB30, pistons and rods to 8000rpm and over 500rwkw in a track car without problems, although I usually tell my customers 7200rpm, 1.5 bar 400rwkw.

Rob

Theres one been sitting in an engine here for 8 months. Still waiting for the rest of the car to be finished before it debuts.

Will be an interesting animal for sure.

Duncan Grand Master

Duncan

Posted
Posted

Hi Rips, I've seen the excellent development work you guys have been doing over the years, but I don't think yours is the first this time :thumbsup: the crank I saw came out of a motor that had been running for a while. I'm not actually sure why it was apart I couldn't see anything wrong with it.

Anyway, I saw this one at Hills Motorsport, I'm sure Mark can provide details to anyone who is interested. I certainly am :)

  • 2 weeks later...
WA_R32 Grand Master

WA_R32

Posted
Posted
We've already finished the worlds first genuine RB33 (ie actually slightly over 3300cc) and it was not quite as simple as we first thought it would be, we have twin 3037s and it will be shipped to Ireland for install in a R33 GTR shortly.

I can also vouch for stock RB30 cranks to 9000rpm 1000+hp, and stock RB30, pistons and rods to 8000rpm and over 500rwkw in a track car without problems, although I usually tell my customers 7200rpm, 1.5 bar 400rwkw.

Rob

keep us updated with the release of this im very interested

  • 2 weeks later...
zebra Grand Master

zebra

Posted
Posted
Hi Rips, I've seen the excellent development work you guys have been doing over the years, but I don't think yours is the first this time :laugh: the crank I saw came out of a motor that had been running for a while. I'm not actually sure why it was apart I couldn't see anything wrong with it.

Anyway, I saw this one at Hills Motorsport, I'm sure Mark can provide details to anyone who is interested. I certainly am :sick:

:) where was that...I didnt see it when I was there last week...wasnt really looking tho

  • 2 weeks later...
Spoolup Mentor

Spoolup

Posted
Posted

My stroker crank is getting closer.

The drawing is finished .Final measurements are 93mm stroke - this will make 3317cc with a 1mm over bore. I will also make a 95mm stroke 3388 cc( but the block will require a little clearancing )

Custom rods will be needed also, these will be I beams and come in the kit as well as pistons.

The first crank should be here early next year.

Dont ask on pricing as the Aus dollar is totally influencing things at the moment.

RB25/26 cranks are next, also SR20 and CA18

N1GTR Grand Master

N1GTR

Posted
Posted

As long as the cost is reasonable (considering there's no social proof to attest to reliability etc) you shouldnt have an issue moving them. Im keeping an eye on your website solely to find more info about that crank option - ive got a spare rb30 block here that (if the price was right) id be happy to put in my GTR and crank out some silly numbers with

Spoolup Mentor

Spoolup

Posted
Posted (edited)

(considering there's no social proof to attest to reliability etc)

I will be building a test engine with the 1st sample - and I will be leaning on it hard - as in very hard with a 50/50 toluene mix.

A Brian Crower 3.4L 2JZ stroker kit ( crank rods and pistons ) in todays market is around $8500, mine will be considerably less. But it still wont be cheap as this is a 4340 billet crank, with 4340 I beam rods and more than likely a custom CP piston to suit.

So dont expect anything less than 5k-6k plus.

Edited by Spoolup
Althotas Proficient

Althotas

Posted
Posted
My stroker crank is getting closer.

The drawing is finished .Final measurements are 93mm stroke - this will make 3317cc with a 1mm over bore. I will also make a 95mm stroke 3388 cc( but the block will require a little clearancing )

Custom rods will be needed also, these will be I beams and come in the kit as well as pistons.

The first crank should be here early next year.

Dont ask on pricing as the Aus dollar is totally influencing things at the moment.

RB25/26 cranks are next, also SR20 and CA18

What capacity are you doing the CA18 to? :P

bubba Grand Master

bubba

Posted
Posted
mmmmmm i think this is a good excuse to delay a rb30 build lol

are mahle pistons really that much better then CP?

LOL makes me want to rush the turbo installation and wind it right up so I can break it sooner and push her to 3.4L.. if only my bank account had the same sentiments lol :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...