Jump to content
SAU Community

Recommended Posts

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

Link to comment
https://www.sau.com.au/forums/topic/216461-rr-problem-without-solution/
Share on other sites

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

its also hisitating when driving

Hi dears

i did all this staff till now and about diagnostics i dont have tool

i changed maf 4 times all same result

i changed cas 3 times all same result

i tryed it without intercooler like direct its littel bit ok but small stuk from 5.5k to 6.5k rpm

and today we will try another turbocharger because some garage said if its littil crap will do same problem

so guys if some one have same this damin problem give us some help :thumbsup:

finally i am thinking that could be ignetion coils !!!!! :(

what mods are u running?

crook w/g actuator?

have u done a diagnostic? try resetting the ecu properly(shorting the 2 pins in the plug method)

dear am using stock turbo with stock wastegate but before i changed it i hade rb20det w/g

to gaine 10 psi

this thing start when i put new greedy front intercooler

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

no man when we changed the cas we adjust the timing by timing light

even i changed ecu with good one also i changed the coils all do same problem

but when we retaind factory intake manifold problem hapen in 5.5 to 6k

but really how could boost come up like antilage in nutral :banana:

i belive its ignition but where i don`t know

  • 2 weeks later...
When the timing is set, is the cas near the centre? Your harmonic balancer may have slipped, and your setting the timing very retarded.

yes brother its in center and with timing gun i got like 12 - 13 degres

all my mods now 3 inch exhust and pod filter with greddy intercooler front mont

and gtr fuel pump also i changed the plugs

yestarday we changed the three wires all long from MAF to ecu and the car runs good

but still i have loosing power in 3rd 4rth gear :P

by the way i am going to buy power fc ecu do you agrre with me ? that it will help me too much

and thanks all for help

What you mean the problem happened @ 5500rpm/6000rpm with the factory plenum?

What other parts are changed?

Full listing please

its noticable loss of power that somthing hold your car moments

and my mods are 3 exhust pod filter intercooler gtr fuel pump thats all now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...