Jump to content
SAU Community

Recommended Posts

Hi guys,

thought i'd post this in here instead of the general section, as this is where the serious stuff happens ;)

My car is currently spoilerless, and i've only done 1 track day at Sandown but would like to do a few more and was wondering if i was to track the car a few times a year, is a spoiler necessary??

I was sorta babying the car at Sandown (33 degrees) and i only got to say 170 clicks on the straight, but i'd liked to give other tracks a go as well, especially Phillip Island.

Withe these the sorts of speeds.is it beneficial and safer to have a spoiler?? I'm not talking some big T wing thing, i'm thinking more along the standard height of a GTT spoiler.

I know they're only functional at certain speeds, and just wondering if recreational track driving see's these sorts of speeds a few times a lap

cheers,

daniel

Link to comment
https://www.sau.com.au/forums/topic/219019-rear-spoilers-necessary/
Share on other sites

wow... ok, guess i wasn't expecting it to be so clear cut, thought it might something like "if you're doing 250+, then... yes"

so in short, even for "weekend" track days, a spoiler can make a big difference and it's probably preferable to have one then?

thanks for the replies guys ;)

I used to have one on my car, took it off and sold it. I never tracked it, but have since been in the guy's car that I sold the wing to which is very similar to my own car. His feels a lot more settled in the rear, which is a bit of a bugbear about my car. I've now purchased a wing and I'll be putting it on before my car hits the track again.

I'll NEVER forget footage that I saw of the BTCC (British Touring Car Championship), where I saw two identical Volvos (same race team), barreling down the straight one after the other.

Halfway down the straight, the rear wing (it was one of those cool touring car T-shaped wings) of the second Volvo rip off and tumble along the tarmac. I'm not sure that the driver noticed, because he kept right into his throttle ;)

Eventually, both cars enter Turn 1 and the first car just brakes and the whole car squats down and gets on with his braking. The second car following a little behind also hits his braking marker, but the car doesn't seem to slow down at all!!! The rear of the car just waddles around helplessly as the lack of downforce and resultant lack of grip meant that he couldn't brake ANYWHERE NEAR as hard as his teammate, let alone attempt making the first turn. He ended up squirming all over the place, and spearing straight off the end of the track at some RIDICULOUS speed, as his teammate casually took turn 1 without a care in the world.

A perfect example of two cars entering a corner with (nearly) exactly the same setup, at the same speed. One with a rear wing, and one without.

I wish I could find the footage to show you guys :wub:

Personally i think aftermarket wings are very hit and miss. If you want to upgrade a spoiler for your R34 then go shopping for an R34 GTR rear spiler, perhaps throw some higher pposts on it to get it up another inch or two.

I suspect the wings that many run actually hurt their straight line speed because of the angle of attack and only unsettle the car in corners as they have rear end downforce but nothing for the front end. Stick with std spoilers for a sure thing. Nissan spend a bit of money on getting them to be a compromised solution for visibility and performance with hopefully livable amounts of drag. Same cant be said for a lot of the aftermarket abominations

I suspect the wings that many run actually hurt their straight line speed because of the angle of attack and only unsettle the car in corners as they have rear end downforce but nothing for the front end.

I don't really know what I'm talking about, but I remember reading somewhere that downforce acts on the car as a whole. Not sure how reliable it is dunno.gif

I'd agree with Roy in that if the rest of your aero on the car is std go with the factory wings. No question that downforce can greatly effect the handling of a car particularly in high speed sweepers and braking zones.

Merli what you say is correct but it is a balancing act. Nissan do their R&D on a car and design the aero so there is a balance between the front and rear of a car. Yes the downforce from a rear wing will act on the whole car but will be biased to the rear of the car. As a result Nissan have designed the rear wing to provide a certain amount of downforce to balance the downforce provided at the front of the car. Obviously this is a highly simplified view as there are other forces at work.

SS8 I would go the R34GTR or GTT wing for your car and retain the std plastic covers under your engine at the front as a starting point.

If you want to upgrade a spoiler for your R34 then go shopping for an R34 GTR rear spiler, perhaps throw some higher pposts on it to get it up another inch or two.

I agree with this plus it give a bit of a sleeper look to the untrained eye. Ill be getting one for my car and Superior in Japan make carbon fiber extended feet and blade for the 34gtr wing so you can always 'upgrade' it for more down force.

http://page12.auctions.yahoo.co.jp/jp/auction/p113441114

ta da.

Cheers

Ross

thanks for the help guys

i was actually thinking of this particular one...

http://page7.auctions.yahoo.co.jp/jp/auction/g58159544 - i figure it's ok to link in here, as i haven't seen anyone else in Oz with one and i like the slightly lower, more angled look.

re: plastic under-trays, unfortunately my front bumper doesn't allow for the factory ones, well not the middle one at least. And the left and right side plastic trays aren't sitting flush with the bottom of the bumper either...

sooo.. if you have more down-force at the front, are you trying to equal that at the back.

Does side aero play any part? My car at the moment...

DSC_1750.jpg

so if i have a bitumen scrapping front bumper, does this necessarily need to be balanced properly at the other end?

as for under body aero, something i'd love to do... i might have to go custom fab for it... east bear under body CF is $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

Your car is so nice. Dont track it. Its too pretty.

As for under car aero, again if factory doesnt fit then dont bother. I think there is far more fun is spendign that money on getting out there and having a ball, and improving your driving. With undertrays that inevitable excursion off the track could be a very expensive mistake :D

Nice car BTW :D

At this stage I'd say just go for the rear spoiler (haven't clicked ont eh link) but nothing too serious. The slight (and I mean slight) imbalance that this is going to cause will be neg until you are right on the edge. You are better off having the downforce on the rear than none at all....

Given teh low front spoiler he is running i wouldnt think you could tell the difference with just a new rear spiler. Remember that the no V-Spec R34s all had the std rear spoilers and the same front bar, but with no undertrays.

Thing is your car looks tough now. Do you really want to throw a big spoiler on it ? :D

^ i'm not sure.... always thought 34's look a bit funny without them, but after lowering my car, and having the full kit on it, it's pretty much passable without a wing, but from some angles, looks a little strange....

k_parts622-img600x450-1151484407myc.jpg

thought this was a good compromise, keeps the sleek look a bit better by being lower than the factory height

adding a spoiler on my old track 1200 coupe made a big diference. kept the rear end much more planted under the bridge at Lakeside, which is a fast sweeper with a few bumps in it. without the spoiler it would hop around and always get a little out of shape there. With the spoiler on, it was much nicer through that corner.

you guys are talking about wings rather than spoilers though. a spoiler is attached to the body of the car across the full width of the device and air only flows over it, like on old school toranas. a wing has an element supported above the body of the vehicle and has airflow above and below it.

Given teh low front spoiler he is running i wouldnt think you could tell the difference with just a new rear spiler. Remember that the no V-Spec R34s all had the std rear spoilers and the same front bar, but with no undertrays.

Thats what I meant in my post.....unless you are driving at 11/10ths you aren't going to notice a difference in the balance of the car with just a rear wing. I am aware that only the 34 vspecs had the front diffusers, however the std plastic covers (which ss8 does not have) under the engine do a similar job albeit not as efficiently.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...