Jump to content
SAU Community

Oil Pressure Level

trel

By trel,
in General Maintenance

 Share

Recommended Posts

trel Mentor

trel

Posted
Posted

Probably been covered before, but I'm interested to know....

What do your gauges sit at at cold start up? Then when normal temperature is reached what does it sit at? ie. idling in traffic?

Mine on cold startup sits just over 4 then when idling in traffic is just slightly over the 1st quarter on the gauge.

This could make an interesting little poll....

Ev.

Link to comment
https://www.sau.com.au/forums/topic/219381-oil-pressure-level/
Share on other sites
Slim Mat Collaborator

Slim Mat

Posted
Posted

RB26DETT here:

Sits on 4 ish when cold. When it heats up it sits on 2 ish. If drive it hard, with some full throttle etc, it drops right down to 1 or below.

As the oil heats up the pressure should drop. Changes will vary between oils, a low viscosity at hot oil (ie: 5w/30 or 10w/40) will have a lower pressure than a higher viscosity at hot oil (ie: 5w/50 or 10w/60). The second number refers to the oils hot temp weight.

R33S2 Grand Master

R33S2

Posted
Posted

I have found that it reads different depending on the oil level, if I have over filled it a bit, it reads higher than normal until hot, if its a bit under it reads just a bit lower, when hot as well. it reads alot higher for the same amount of less does.

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
Anyone think mine is too high?

R32 GTR, freshly built, n1 oil pump

cold 8 bar,

warmed up 4

driving hard between 3-4

Oil - Mobil 1... forget viscosity of it...something like 10-50 or 5-50..

About the same as mine.

When its cold, its just under 8 bar tho.

Mobil Synthetic S 10W-40

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...