Jump to content
SAU Community

Need Help Fitting A Turbotech Boost Controller Onto A R32 Gtst

Sydney GTS
 Share

Recommended Posts

Sydney GTS Rookie

Sydney GTS

Posted
Posted

Hi guys.

I need help installing one of the manual boost controllers onto my r32 gtst.

I cant for the life of me find where to insert it tho i have found plenty opf manuals for the r33, nothing for my 32 can i find.

I really need pics so if anyone has a pic of where they put theirs on their 32 stocky then plz let me know.

Thanks in Advance.

R 2 THE J Rising Star

R 2 THE J

Posted
Posted
woul dlike to know this too :banana:

thanks

I'm pretty sure its the same for a 32 but this is what i did in simplified form.

- Locate solenoid. Take off the top hose and put a bolt in it to block it off and cable tie to secure.

- The hose on the bottom of the solenoid should be connectod to a T piece.

- Remove the T-Piece.

- ur boost controller will replace this.

- As in the pics of Turbotech...follow instructions...bottom barb to turbo..side barb to actuator.

MAKE SURE YOU UNPLUG THE SOLENOID.

Hope this helps!

Sydney GTS Rookie

Sydney GTS

Posted
  • Author
Posted

Searched for like 2 hours and nothing on the rb20's only 25's.

I found the wastegate and there is a line coming from the bottom of it and im guessing this is the line i need to put it on.

I dont think us rb20's have this solenoid and stock t piece so im guessing i have to cut this line and put it in.

If i get a confirmation that its the correct line ill put a pic so others can see for the rb20's

GeeTR Grand Master

GeeTR

Posted
Posted

No offence, but I honestly think, if you cant figure out how to install a bleeder to your import by understanding the dynamics, or find the answer on the interweb, you should be taking it to a mechanic.

  • 3 weeks later...
r32woohoo Rising Star

r32woohoo

Posted
Posted

Come on guys im sure you can be a little more helpful, they're obviously new to this. I had no idea either when i first started, and i didn't bother asking questions like this coz i knew this was exactly the type of answer i would receive.

anyway, 32s don't have a std boost solenoid so don't worry about that

If you can see the turbo it's fairly easy,

theres a hose coming off the turbo housing to the wastegate actuator, cut the hose and plumb the controller into it. you might need to get a longer hose. I cant remember which way it's supposed to face so check your instructions but as far as i remember, the nipple opposite the big screw is supposed to face the wastegate actuator and the other horizontal nipple goes to the turbo housing

sonoramicommando Collaborator

sonoramicommando

Posted
Posted (edited)

r32woohoo is spot on - r32 has a pneumatic wastegate actuator and it alone controls the max. boost pressure & when the wastegate opens.

the controller goes between the wastegate actuator nipple and the turbo compressor housing nipple.

he is also spot on the assessment of some ppl's attitude on this forum - we've gotta start somewhere, we've all started out as a newbie.

it helps if you understand how it all works but i really don't think we need the answers like "if you can't understand/do this, take it to the mechanic". some ppl DIY to save money, others do it to understand and learn. this is not really personal to you GeeTR, just an observation and a suggestion.

cheers

sam

Edited by sonoramicommando
bevo89 Contributor

bevo89

Posted
Posted

cheers guys.

i knew where the hose was and what i had to do, just wasnt sure if the 32 had a solenoid like the 33 does.

but thanks for the feed back. it does clarify things when someone that knows exactly what they are doing (not people like myself that sorta no what to do) pass information on to others so they now know what they are doing

cheers again

drew

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...