Jump to content
SAU Community

Recommended Posts

hey guys

im in very sad state of mind after waiting almost a year to get my car on the road iv got a major problem

ok here i go, i had an r33gtr which had a forged motor with a n1 pump, i put the motor into a r32 gtr

all way going well until a couple of hours ago, after my mate finished adding the final touchs to the pfc we took it for a drive got a bout 300m down the road, and the car stalled, tryed to roll start (kick the clutch while moving) all 4 wheels locked up.

at this stage i was very worried, it felt as if the motor seized mind you the motor is only bout 2800km old built by race pace...

so we pulled of the cam and cam gear covers of to see if anything broke,

but nothing but i did notice there wasnt allot of oil on the cams and underneath the cam covers was dry as a bone, so something to do with oil pressure,

i do have any aftermarket apexi oil pressure gauge that wasnt showings any sign of low oil pressure. and didnt here any knocking or breaking sound

the motor was running perfectly in the r33gtr which i use to own, now is a wreck coz it got hit but no where near the motor, i did get a breaker bar and crack the motor every few week to keep everything lubricated, only thing iv changed on the motor since it was in the 33 are hks dump pipes, bigger exhaust, changed plugs,oil and filter

oh and btw my mate is a mechanic and know what his doing when it come to rb26s and will try and get it stripped down tomorrow but i need to know if this has happen to anyone before im very worried and need to sleep at night

some please help thanks guys

mods to the motor are

Forged Pistons (Arias)

-Metal head gasket

-N1 Oil pump

-ACL bearings

-New crank

-Head Work (just general tidy up)

-New belts

-Engine Blue Printed

Link to comment
https://www.sau.com.au/forums/topic/220607-rb26-major-problems/
Share on other sites

hey guys

im in very sad state of mind after waiting almost a year to get my car on the road iv got a major problem

ok here i go, i had an r33gtr which had a forged motor with a n1 pump, i put the motor into a r32 gtr

all way going well until a couple of hours ago, after my mate finished adding the final touchs to the pfc we took it for a drive got a bout 300m down the road, and the car stalled, tryed to roll start (kick the clutch while moving) all 4 wheels locked up.

at this stage i was very worried, it felt as if the motor seized mind you the motor is only bout 2800km old built by race pace...

so we pulled of the cam and cam gear covers of to see if anything broke,

but nothing but i did notice there wasnt allot of oil on the cams and underneath the cam covers was dry as a bone, so something to do with oil pressure,

i do have any aftermarket apexi oil pressure gauge that wasnt showings any sign of low oil pressure. and didnt here any knocking or breaking sound

the motor was running perfectly in the r33gtr which i use to own, now is a wreck coz it got hit but no where near the motor, i did get a breaker bar and crack the motor every few week to keep everything lubricated, only thing iv changed on the motor since it was in the 33 are hks dump pipes, bigger exhaust, changed plugs,oil and filter

oh and btw my mate is a mechanic and know what his doing when it come to rb26s and will try and get it stripped down tomorrow but i need to know if this has happen to anyone before im very worried and need to sleep at night

some please help thanks guys

mods to the motor are

Forged Pistons (Arias)

-Metal head gasket

-N1 Oil pump

-ACL bearings

-New crank

-Head Work (just general tidy up)

-New belts

-Engine Blue Printed

Does it turn over on the starter with the plugs pulled?

Does your fuel pump prime on ignition?

You have spent a sizable chunk of cash on your motor, why not take it to someone who knows what they are doing before pulling the motor? :P

no the motor dosnt turn over at all, not even with a breaker bar, and my mate is a mechanic that knows what his doing, not his fault engine was running mint for bout 10mins then all of a sudden seized up and locked up all four wheels,

engine is getting pulled down today to find the problem

All injector seals in? drain the oil?

I have no honest idea but I read the other day a person having the same problem with injectors which are not installed correctly and was flooding the engine?

Hydrollic lock i think its called

Edited by DECIM8

im over this car, i was so close to stripping it down and selling it as parts,

but my mate didnt have time to pull it apart today but will early next week, but looks like i will be folkong out for another build,

but the funny thing is we never hear nothing break, and also no metal shavings when we drained the oil

it might seem like a dum question, but when you started for the first time did you take the oil cap off and make sure the cam lobe you can see from there had oil on it????

was the correct seal used on the N1 oil pump?

cause if a breaker bar wont turn it over you have either got A: a siezed motor B: a dropped valve or C: dropped a big end cap?

but from what you described above i wouldnt be surprised if the main bearings have spun and it the cradle pressure clamping the crankshaft.

good luck with that one bro, i feel for ya...

atleast when mine stopped going you new what was wrong with it cause number 3 piston was hanging outta the block.

for it to sieze solid and not make noises, it will of spun a main bearing. the cambelt will snap at the wieght of the whole car. if its just the head siezing, its a pretty damn strong belt!!

so no oil in the head.. all of a sudden. somethings blocked. does it have an oil cooler with remote filter?

the belt isnt snaped, i dont have an oil cooler or remote filter but i did notice there was thick gunk underneath the cam covers but not really any oil there, from what i can gather i think the oil pick up is blocked but wont no until we pull it apart,

if the main bearing is spun will it of damaged my crank? or will i just be able to replace the bearings?

anyway thx for this guys im pretty stressed out atm

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I don't like "actual computers" for in car use. They take time to boot up, have OS annoyances, and so on. Arduinos etc are ready to go a few seconds after power on, don't mind being agressively powere cycled, because everything is non-volatile, don't mind being shaken and stirred.
    • As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
    • Being a race car, and being in the era of the Arduino, one would think it would take little effort to build a controller to do the spraying based on a real physical measurment. Waaaaay back in the dim dark AS days, JE "designed" (as in, he had help) a microcontroller based intercooler spray system. It watched the difference between a temp sensor stuck on the core and one in the free air in front of the cooler, and if the temperature difference exceeded a (settable) threshold, it would activate the sprays. Thus, it only ran water when there was an actual need for water. If you stop to think about the actual physical things that are going on in that stack of coolers, there's probably at least a couple of triggering conditions one could come up with, and one could probably even run one pump with more than one solenoid valve, to allow water to be placed where it is needed, or at all points at once (if it is needed at all points). We're in the age of science baby. But.... I suspect that intercooler water sprays are on the forbidden list in most circuit classes, no? So only good for Targa type stuff?
    • I'll just leave this with, holy shit, those cars at work are awesome, and this will look wicked!
    • Could you modify this duct so instead it pushes the extra air through the radiator too and not down and out? For temps, I know it's not the greatest idea, but as a bit of a last resort, you could use a very intermittent misting spray onto the front of the coolers/rad. You don't want to be soaking them such that water is dripping off, but a small most on/off so that the water evaporates. That point of it constantly evaporating, rather than being soaked in water, will pull a LOT of heat out of the cooler. I'm literally thinking just the little mist sprayers for a garden from Bunnings. Being in a low humidity climate it will help even more! The other trick if you want to be ghetto is some shade cloth hung in the opening, and keep it wet. Pretty much now it's acting like an evap cooler on a house, but cooling the air you need to use to cool the radiator...   On a topic to think about too though, when air enters through the bumper, is it all nicely ducted from the edges of that opening back at a nice angle, or is it like most cars, and the edge of the opening just stops, and suddenly it's wayyy wider behind that? If it does the later, get it shrouded out at nice angles. When that opening changes too rapidly, it can actually cause a high pressure zone between the front bar and radiator, and limit air flow into that area, which means less air for cooling, as it effectively stalls the air, AND adds to drag...
×
×
  • Create New...