Jump to content
SAU Community

Recommended Posts

got my screamer on today, at tilbrooks, they also built a new front pipe for me,

i know screamers are ment to be loud on boost, but mine vents to atmosphere on idle to!

it sounds a bit like drift pipes all the way through the rev range, but when on boost, it screams, thats the only part i wanted....

can i get it quiter? when driving off boost?

cheers

craig

Link to comment
https://www.sau.com.au/forums/topic/220946-screamer-dump-pipe/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

well there are proper ways of making them, they obviously haven't created a good seal between the wheel and the screamer pipe....should have asked who makes good ones before you went and got it, i could have refered you to a bloke who makes second to none exhausts.

ive made a couple in the past for mine, and i didn't like it.

can i ask how much you paid just out of curiosity?

As ryan said the actuator hasnt been seald off properly. So the exhaust wheel is leaking into the screamer pipe and causing lots of unwanted noise.

The one an donly place to get a great sealed Screamer/Front/ Dump pipe is Andrew from AM Performance.

He made me one up for the 32 and it was awsome. Could drive past cops and they had no idea what was lying beneath.

Take the screamer off and get the maker of it to adjust it to stop the leaking gases.

i got it from just jap, they are a tader on here, so i thought it would have been

one of the better ones on the market. i paid $110 not including P&H.

do you think this is somethin tilbrook is capable of fixing?

As ryan said the actuator hasnt been seald off properly. So the exhaust wheel is leaking into the screamer pipe and causing lots of unwanted noise.

The one an donly place to get a great sealed Screamer/Front/ Dump pipe is Andrew from AM Performance.

He made me one up for the 32 and it was awsome. Could drive past cops and they had no idea what was lying beneath.

Take the screamer off and get the maker of it to adjust it to stop the leaking gases.

thats it dude, andrew used to do alot of work for us at my other work....second to none workmanship.

most would kno of the screamer i had on my 32 yeh

and u couldnt tell it had one at idle or up to 3300 revs roughly

well that was made by AM Performance

there is a pipe that goes straight up to the compressor wheel instead of just a plate, and it does not leak at all.

get GTR kiet to send u a photo of it coz i sold it to him just earlier tonight

im sure Simon can fix it :(

i got it from just jap, they are a tader on here, so i thought it would have been

one of the better ones on the market. i paid $110 not including P&H.

do you think this is somethin tilbrook is capable of fixing?

the factory wastegate leaks, i've seen a split dump/screamer that sealed on the inside of the turbo exhaust wheel, yet it still sounded like a truck idling.

screamer on stock turbo sounds like crap anyway...

just get a external gate n youll b A ok....lol

Screamers are gay and give all us Skyline drivers more police attention, no to mention bad reputations with the noise-hating public. You are begging for a defect - fist cop that sees/hears you will ream you hard.

Screamers are gay and give all us Skyline drivers more police attention, no to mention bad reputations with the noise-hating public. You are begging for a defect - fist cop that sees/hears you will ream you hard.

amen to that.

i got impounded coz a cop heard me from like 500 metres away.

they call it excessive noise lol

hence why mine is now sold

Screamers are gay and give all us Skyline drivers more police attention, no to mention bad reputations with the noise-hating public. You are begging for a defect - fist cop that sees/hears you will ream you hard.

Well said Nightcrawler.....i think screamer pipes sound good on a track/drift car.....when sideways peaking off its head yeah it sounds crazy....not on the streets dude....

got my screamer on today, at tilbrooks, they also built a new front pipe for me,

i know screamers are ment to be loud on boost, but mine vents to atmosphere on idle to!

it sounds a bit like drift pipes all the way through the rev range, but when on boost, it screams, thats the only part i wanted....

can i get it quiter? when driving off boost?

cheers

craig

Do u actually have an External gate set up or split dumps?

Coz if u have an External gate set up.. and have a screamer pipe and its venting on idle. I'd say ur External gate is f**ked...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...