Jump to content
SAU Community

Recommended Posts

Here's the story - The car is a series 2 R33. It hasn't been driven for over 6 months now (apart from in and out of the drive way), however i usually start it and let it run once a week. Last time i started it, it ran fine for a couple of minutes then a tapping noise started to come from the engine. It sounds to be coming from the back of the engine and will get faster as the revs increase. I'm thinking (hoping) it's just the lifters, however i'm worried that it could be piston slapping or something... Any help will be much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/221911-tapping-noise-in-rb25/
Share on other sites

does the car still have good power?? i rekon its noisy lifters try putting some fresh oil in it see how you go

I haven't driven the car since the noise started, however the last time i drove it (over 6 months ago) it was still making good power. I plan to try changing the oil soon, if that gets rid of the noise does that mean it's definitely the lifters? Is it even possible to spin a bearing under idle? The noise came on suddenly under idle without previously being driven.

I haven't driven the car since the noise started, however the last time i drove it (over 6 months ago) it was still making good power. I plan to try changing the oil soon, if that gets rid of the noise does that mean it's definitely the lifters? Is it even possible to spin a bearing under idle? The noise came on suddenly under idle without previously being driven.

ok mate well just put some fresh oil in it let it run the noise should stop for you, there is no why you can spin a bearing at idle i have heard louder lifters then that before after rebuilds so dont be to worried

thats not a good noise.... sounds a lot like one of the pistons is slapping the wall....... very similar to how mine sounded before we pulled the motor apart and found a lot of bad :<

you need to get this checked out by someone good asap.. fingers crossed for you bud, hope its just lifters.

mate ive heard dat same sound b4 on a rb25det neo that was bought from a reputable workshop. everyone said lifters, so i went to get the shims checked. All were within spec, so wasnt lifters. motor than got pulled apart. bearing were all fine. even compressions test came back fine lol.

And it was the EXACTTTTT noise, coming from the EXACT place. motor was stil making the same power, and i drove it for 5000kms (until the workshop replaced the motor for me) and it didnt get any worst or damage anything.

I had exactly the same problem except it was a little different when i started the car it would go tick tick tick for a few moments then after a bit it would stop but when i was driving i could hear it when the windows where down when i was driving,anyway about a week ago i did an oil change with some motul 4100 turbolight oil and its seemed to have fixed the problem.....the oil is expensive but give it a try it fixed my problem it may fix yours

post-38649-1212478847_thumb.jpg

Edited by benkoau

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...