Jump to content
SAU Community

Recommended Posts

Hi,

A mate of mine is having troubles with his R33.

As soon as it hits about 5500rpm it just stops accelerating and starts back firing. or if it doesnt back fire it just stops reving and stays @ 5500rpm...

We are certain that is not coil packs as we have had many coil pack issues before and this isnt the same.

The car had a Power FC, Z32 ADM and a 044.

The now has a Stock ECU, AFM and fuel pump.

Also today is the first time the car has been driven since August..

Any help appreciated!!

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/
Share on other sites

nah if its running fine up to 5500 rpm it wont be plugs or fuel, if it was either of those it would be coughing and spluttering right through the rev range,

but will need a few questions answered before being able to tell what it is causing it, is the afm still ok, have you swapped it with that of another car?

is the car running standard boost. if it had a z32 on it was the setup outflowing the standard afm? if so take the boost back down to standard.

R33, variable timed yes, is the solenoid still operational that lets oil flow to the lifters?????

the ecu alters fuel values when the system is activated by the rpm, flooding perhaps and detonating violently?

if so unplug the O2 sensors and leave them off for the time being as the ecu would be compensating for the richness,

also unplug the ecu temp sensor, this will force the ecu to go into normal operation as if the engine had warmed up.

is the base timing correct, assuming it was running a aftermarket ecu, afm, etc was this altered at all?

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3943506
Share on other sites

It seems to have lost alot of power throughout the hole power range. But hasnt lost any boost.

Also little puffs of black smoke seem to come out the rear so it couldnt be the fuel pump if its running rich??

Could it be the afm??

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3945482
Share on other sites

It seems to have lost alot of power throughout the hole power range. But hasnt lost any boost.

Also little puffs of black smoke seem to come out the rear so it couldnt be the fuel pump if its running rich??

Could it be the afm??

Almost a thread a week on this these days… *sigh*

Your running increased boost on the stock ECU. Its therefore having a fit/hernia/spaz etc etc.

Back off the boost, car will return to normal as its closer to factory. RB25 ECU's don’t like much over standard boost pressue in many instances

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3946101
Share on other sites

It is a constant problem at the 5500rpm mark? My car is having similar issues, but its temperamental. Some days it drives great, other days its terrible, and of course whenever I take it to the mechanic it decides to have a good day, or half-week as it were last time.

In any case, next time it plays up I'm driving it straight to him. I'll post here on what he finds.

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3947828
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...