Jump to content
SAU Community

Recommended Posts

I have r32 n1 turbos on my rb26 and have oil leak from back turbo is it easy to rebuild or cost a lot. may replace them i have been offered 600 for the pair.

it will cost you a bit to rebuild them. 600 is a low offer for n1 turbos

Link to comment
https://www.sau.com.au/forums/topic/226112-r32-n1-turbos/#findComment-3981019
Share on other sites

new oil seals, check bearings and balance about $500 ea. If you need new bearings as well add another 500ea. They are worth about $2kea new.

But, they are not really a good turbo. Useful for some poor bastard (like me) who has to run standard 32 n1s because of race rules, but the 34 n1 or 2860s are much better for most uses

Link to comment
https://www.sau.com.au/forums/topic/226112-r32-n1-turbos/#findComment-3982455
Share on other sites

new oil seals, check bearings and balance about $500 ea. If you need new bearings as well add another 500ea. They are worth about $2kea new.

But, they are not really a good turbo. Useful for some poor bastard (like me) who has to run standard 32 n1s because of race rules, but the 34 n1 or 2860s are much better for most uses

IN GOOD CONDITIONS DO YOU KNOW HOW MUCH BOOST THEY ARE GOOD FOR

Link to comment
https://www.sau.com.au/forums/topic/226112-r32-n1-turbos/#findComment-3983940
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...