Jump to content
SAU Community

Recommended Posts

Woo on 2nd trails Newmans by 10 seconds after stupid 9 stages of dinky dye motorkhana crap today. Sunday will bring the mountain, the Skelta looms large behind!

They have motokhana stages?? I need to do this rally one day!

I always thought Lake Mountain could have been an epic Rally if they put a motokhana style challenge in the carpark at the top.

It's the one thing I really miss about Dutton event is whacking the handbrake everywhere! :)

Well, it wasn't really a motorkhana as such, not tight enough to require the handbrake.

It was a 1.1klm loop using part of the V8 Supercar track.

Would have been an excellent Prologue and sponsor ride course, but hmmm, to travel 1,200klm for one day of it? Not so sure.

A perfect world would have seen friday arvo/night passenger and Prologue there, and up to Mt Stuart for Saturday/Sunday

Mt Stuart is an awesome challenging piece of tarmac. :)

that was fun to watch team Woo.

the key to that video for me was the commitment. at one point you are accelerating upto and over a crest that is then followed by a 8 right into 8 left. from the incar you cant see where the road is going over the crest but if you was reading the road (bad thing to do) you could see it was going to go left. its that commitment to keep accelerating where the average punter would go screw what the idiot to my left is saying im gona lift off that wins plastic.

Also did anyone elce notice the clutch kinking, sideways action, wheels in dirt action that was closely followed by a crowd of people or fluro vested photographer? :blink:

Thanks guys.

And yes, big congrsats to Russ and Sarah, I'm very very proud of them both. It really was the perfect outcome, couldn't have asked for anything better to be honest.

Well, actually, it would have been a lot better if Coop didn't spin it and bang up the GTR again.

Our 4:09 run, quite different from Russ's 4:09 run :P;

Huge well done to Timmy, Russ and Sarah, Coop, Wade, Gary, Peter, we had lotsa fun, and it wouldn't be the same without the fantastic NQ hospitality :D

Nice one mate. How much time did you shave off from your first run to your fastest one out of interest?

Nice one mate. How much time did you shave off from your first run to your fastest one out of interest?

First run, Russ/Sarah, Woo/Me and Coop/Wade all did 4:20's thinking there wouldn't be much more in it, maybe a second or two would be fast.

Second run up the hill Russ/Sarah did a 4:11, Woo/Me did 4:10 and Coop/Wade did 4:16.

3rd run was fastest with Newmans and Team Wooster doing 4:09's

Yes, interesting question Snowy.

I was interested too to see the difference. First run we attacked as we would any other tarmac rally stage that we would see once, and we did a 4:20. So that's a little over a second a kay slower. On subsequent runs, we still drove purely on the notes, I wasn't trying to remember it, but of course you kind of do anyhow, plus you're 100% confident with the notes after a pass over them.

The 4:09 run was our 3rd pass.. Other runs were consistant 11's and 12's.

One thing that came out of the weekend was our writing of notes, we only had two passes over the course, wrote the notes, and they were spot on. We gave a copy to Russ and Sarah and they proved the notes were quick. They had different notes last year and mangaed a 4:12 in the time machine R35. Very happy with that :P

Yes, interesting question Snowy.

I was interested too to see the difference. First run we attacked as we would any other tarmac rally stage that we would see once, and we did a 4:20. So that's a little over a second a kay slower. On subsequent runs, we still drove purely on the notes, I wasn't trying to remember it, but of course you kind of do anyhow, plus you're 100% confident with the notes after a pass over them.

The 4:09 run was our 3rd pass.. Other runs were consistant 11's and 12's.

One thing that came out of the weekend was our writing of notes, we only had two passes over the course, wrote the notes, and they were spot on. We gave a copy to Russ and Sarah and they proved the notes were quick. They had different notes last year and mangaed a 4:12 in the time machine R35. Very happy with that :thumbsup:

You tempted to write your own notes for targa now?

Thanks Harry!

Nothing wrong with John's notes at all in my eyes mate (in fact they're superb), but if time and money were plentiful, then yes, writing our own notes would be awesome. That will have to wait until Tim and I secure a factory drive which would allow for a few weeks writing and checking notes.

I know damn well if I was a Tassie local I'd write my own. :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...