Jump to content
SAU Community

Recommended Posts

Hi everybody,

I bought my gtst with all the basic mods and its power fc which was tuned for 100 octane petrol. The previous owner says it was tuned on a shell petrol which didnt have ethanol in it (not V-power racing which i dont like as its 20c more), so my question is since if run i it on 98 octane is there something i should adjust on my hand controller to accomodate to the lower octane petrol?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/230188-r33-tuned-for-100-octane/
Share on other sites

Hi everybody,

I bought my gtst with all the basic mods and its power fc which was tuned for 100 octane petrol. The previous owner says it was tuned on a shell petrol which didnt have ethanol in it (not V-power racing which i dont like as its 20c more), so my question is since if run i it on 98 octane is there something i should adjust on my hand controller to accomodate to the lower octane petrol?

Thanks!

Well you've contradicted yourself.

Tuned for Shell without ethanol means it was V-Power, the 98

The 100 was V-Power Racing, which had ethanol, and is not discontinued

So based on what you said, your car is already tuned for 98... so if you've been putting 100 in there, you've sadly been wasting your money.

So if you just muddled yourself and you indeed WERE tuned on 100, you will need to be re-tuned for 98. Simple as that

Yeah somehow the previous owner had 100 octane shell petrol in it for the tune, he said it didnt have ethanol in it but he may have been mislead. Who knows.

So a WHOLE retune is required to have the car running optimally?

I'd check the knock levels on the handset first, if the readings are OK, I wouldn't worry too much about it and just get it done whenever [the tune].

Sounds like the last owner didn't know what they were talking about [some confusion over fuels], so it could be that your tune is already OK as it is.

Suck it and see.............

Well you've contradicted yourself.

Tuned for Shell without ethanol means it was V-Power, the 98

The 100 was V-Power Racing, which had ethanol, and is not discontinued

So based on what you said, your car is already tuned for 98... so if you've been putting 100 in there, you've sadly been wasting your money.

So if you just muddled yourself and you indeed WERE tuned on 100, you will need to be re-tuned for 98. Simple as that

V-Power racing has been discontinued on the gold coast where i am and i suggest in many other places

this thread is redundant

100 octane is standard factory issue.

skylines from factory are tuned for 100 octane cause in japan thats the lowest octane they have....exept diesel obviously.

stick 98 in the tank and alter the timing the timing a couple of degrees.

Knock levels aren't too bad actually, i had some trouble with it before but i think the boost wasn't tuned correctly (liked to spike).

I switched from bp ultimate to normal v-power last week and i havent seen knock over 25.

I'll take it to the drags and see how i go.

Nizmonut, so i retard the timing by the odd degree?

in summer you will notice a raise in knock

Yeah thats definately true actually, summer was when i was having problems....

I'll let you know when i have time to do it, and we can sort something out, thanks for offering to help. (sick r33 btw :()

this thread is redundant

100 octane is standard factory issue.

skylines from factory are tuned for 100 octane cause in japan thats the lowest octane they have....exept diesel obviously.

stick 98 in the tank and alter the timing the timing a couple of degrees.

lol. that is a good one. 100octane is the lowest in japan. I'm sorry mate but that's simply not true. having been to japan many times, and driven cars in a number of different cities (tokyo, osaka, kyushu, chiba, saitama) I can tell you 100octane is pretty much the bees knees. hi-oku blend. regular unleaded there is like 94 octane. good fuel 98 or so, and yes they have hi-oku 100ron fuel too. but no factory car would be tuned un-able to run on 98 or even 96. this myth came about when high performance cars designed to run on 95 or 96 octane fuels were run on fuel in aus that at the time was 90-92 at best. things have come a long way since then and the gap between japanese fuel and australian fuel is not that great.

V-Power racing has been discontinued on the gold coast where i am and i suggest in many other places

Is United doing the same thing with their Boost 98?

Unless the car is tuned on the edge, running Vpower 98 fuel shouldn't be a problem. You will get more petrol into the cylinders compare to vpower racing and find that the car is alot richer. You will be down on power as well.

Have you try the freedom 98? It has 10% ethanol as well and is only 2 RON lower than Vpower racing. If knock reads higher with the freedom fuel then pull the timing back by a few degrees until knock reading goes back to normal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...