Jump to content
SAU Community

Recommended Posts

OK, heres the story so far. ive only recently had a 100,000km service (less than 1000km ago) in which they did all the usuals plus replace the transmission fluid. after that service, within a few hundred kms i experienced problems with the power when just cruising at a constant speed. the power would die and the engine revs would drop off, then jerk back up to rpm. the 4WD light would soon come on and also pressing the overdrive button wouldnt drop the gear down to 3rd.

i took it back and they replaced the transmission fluid, from the brand they put in to the genuine nissan fluid and also put 2 earthing straps on the body and engine as they beleived the 4wd was an electrical fault.

it was fine for a few days but the problem has come back with vengeance. today the power was dropping off harshly and it almost felt as though the car was almost dragging, and 4wd light on again.

this seems to happen intermittently, the rest of the time the transmission is flawless, WTF is going on?

perhaps its not the auto transmission but the transfer case?

argh i hope this doesnt drag me down into a money pit of hell

im in canberra by the way if anyone knows some specialists. ive been to autotech so far

Edited by zoomzoom

find the bleed nipple on the transfer case, situated at the top near the hose connectors , connect clear hose to nipple, run engine, loosen off nipple slowly, allow flow until no more bubbles come out. tighten nipple and check resovoir whilst engine still running. Dont allow the resovoir to get too low during bleed.

As Chook said, but I had a mate help me. Ran the resivor(??) down to almost empty, topped it up with fresh (bright red) fluid, drained it again, topped it up again. 3 times makes sure it's only fresh fluid in the system and all has been good since.

Cheers, Greg.

another follow up question:

is the fluid used in the tranfer case and attessa system similar to the transmission fluid? is it capable of retaining water?

ive always found this problem to be heat related, as it occurs after the car has been used for a good 40 minutes or more.

is it possible that theres water which vaporises under heat and causes problems like when you get water in brake fluid and it messes with the brakes?

im thinking if i bleed the air and theres still water in there it may be a pointless exercise. just replace the whole lot im thinking

it was checked at the 100k service but was clean so it wasnt replaced. i would have preferred it to be changed in the first place but ill have it done this week.

the car was especially bad on the drive home today. there was a 10km stretch where the power was dying on and off about every second.

i bloody hope its a simple fix :)

it was checked at the 100k service but was clean so it wasnt replaced. i would have preferred it to be changed in the first place but ill have it done this week.

the car was especially bad on the drive home today. there was a 10km stretch where the power was dying on and off about every second.

i bloody hope its a simple fix :(

There is nothing special about the Nissan fluid except the price. You can use the same ATF in the auto, Atessa and power steering.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...