Jump to content
SAU Community

Recommended Posts

Hey guys,

Im getting pissed with this engine problem, Ive put it off until now but now its just painful. Just so you know I had my belts changed along with a endless amount of parts so its hard to pinpoint the issue.

The problem is a slow start every time I park the car and turn it off for 1-5 hours more than that and it has no issue starting. The engine will take 4-6 seconds to fire and I will try ignite, stop and go again more often than not its 3 attempts to turn it over. This then greats me with a mid idle not the typical starting warm up idle. It can often just fire cylinders slowly as if cylinders ignite one by one very slowly.

Saying this when I walk out to start the car in the am before work she fires with no issue.??!

Im aiming at a few items.

Alternator - Its an R34 alternator so I find this hard to believe, I had no issues before this time and the car will not stall and holds a steady charge even when sound system is thumping for 30mins or so.. I dont feel that it can be faulty if its still doing its job.

Starter - The clutch was changed in this procedure so Im thinking it may be this, How extactly do these work could it perhaps be a weak voltage drop to this item?

Belts - I fitted gates belts when I start the car I notice the power slowly raises stops then continues from 12v to 14.8 or close Im thinking when cold they shrink which is great for long term in the short term they sqeek so loudly when it fires and are so tight they dont spin correctly on ignition. Perhaps they are stopping it cranking correctly.

So Fuel pump, installed it when stock had no issues like this. Eliminated.

Injectors - checked

Sparks - Brand new powered with spitfires.

So my money is on starter but what does someone else think?

Link to comment
https://www.sau.com.au/forums/topic/236202-slow-starting-engine/
Share on other sites

not good Nath :)

hope you find the prob soon!

just wondering... is it only the gates belts that shrink that much? or do standard ones do it to?

cause i was going to get gates belts all round but after reading that they dont sound too well...?

cheers mate

Jaye

This might sound crazy... What brand/type of oil do you use? Sounds exactly like a problem on my dad's VS commodore. He had the problem when he was used Pennzoil semi synthetic, so far all other oils he has used do not seem to give a problem, might be worth a look.

Further investigation on other vehicles suggests its a rooted starter.

How do starters work as im expecting the cable to badly connected or similar. I know they would be grounded and positive somewhere its just checking connections.

Supposedly the starter requires more power when it absorbs heat, this inturn needs a bigger current when warm which it cant draw because of either clutch dust or bad connections. The reason it wont start when stopped for the first hour is because the heatsheild blocks most heat but cant resist it for more than 30 mins or so.

Sounds like total crap I know but its actually true, alot of people have exactly the same problem in almost every single car even out of factory brand new!

Now I just need spare time and a hoist.

Crap!

I would say from listening to the problem, it COULD be the battery very possible although its highly unlikely.

I would put my money on the starter motor though bit odd only starting from cold though, woulda thought it would be the otherway around.. awell hope its fixed asap.

my first thought was too far advanced timing

but then you said that it was a warm start problem

i think it might be a combination of what lunjiaow (vince) said and what ive said

(sometimes a hard start is too advanced timing - a very easy start is timing too retarded)

  • 8 months later...
  • 2 years later...

Have you changed the timing belt recently? If so, did it start doing it afterwards?

I have the same issue, picked up a 34 gt, the timing belt was done 5 weeks ago (before I picked it up). Ive been looking over the same things and none have fixed the issue. However, looking at the CAS the previous owner has marked it but it doesnt look to be correctly aligned with the marks, but not sure on this as the marks were made on the washer......

It seems to be in an advanced position.

I dont think its anything to do with solenoids or batteries. The rb25s are all built the same. The series 2 doesnt have this problem. It seems to be a regular occurance on the neos. They start fine cold but when warm sound like they want to start but just dont as if no fuel or spark is present. I think it has something to do with the neos design or tune.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • +1. Good thing is people wont tailgate you for a while
    • If you have a RB25DET NEO AWD motor, you will need this: https://www.hioctanedirect.com/ASR-RB26-RWD-Street-Comp-6.5L-Sump-Suit-R32/33/34-and-VL It is made for the AWD motor, but makes it fit a RWD setup and gives you a new pickup. Just one thing, the pickup sits quite forward, compared to a conventional RB25DET RWD motor. This may or may not have contributed to my previous AWD -> RWD shitting the bed at the track.
    • My car is also flex tuned. It's worth mentioning it (the LS1 ECU) has a 1D table for E85 addition and just uses the ethanol stoich part as the second point of reference. It also as a 3D timing map for Ethanol adjustment. You would think this isn't enough but it works pretty damn well. That said, I wouldn't want it in turbo application. It's like lifting non-natty, or taking meth. It gets you unrealistic results that break down more things going forward. If people used it to make the same amount of power they do on 98 then it'd be one thing. But people use it, crank it up to eleventy million PSI, it doesn't knock - but it pushes the point of failure to another, more expensive thing to break. Every time I see someone make 280kw on 98 and 350kw on E85 on the same equipment I just cry a bit and really wish they would just stay on 98 in that exact scenario. It's bad for you. 
    • This is kind of what I was thinking but the temp sender wire and the two pressure switch wires run through the starter subharnes and I eliminated the two pressure switch wires completely.  @GTSBoy I have a can gauge with unusually bright warnings should the oil pressure fall so the factory light isn't needed. I need to dig out my wiring diagram and see if I can sort this out.
    • It's a valid point. And it is doable with the Nistune. But I'm not inclined to flex it the way Nistune does - certainly not on a Neo ECU. They're already pernickety enough to tune just one one fuel. And of course, I'm not that interested in putting in a Link or similar, on a daily. With the stock ECU, stock looking turbo, etc etc, I still stand a chance of surviving a run-in with the plod. Last time it went over the pits (which was for the transplant, for because of a run-in with the plod), the Nistuned ECU did not even raise an eyebrow. They want to see a stock ECU running the engine, and they are happy to see it do so without the check engine light** on. Never mind that the Nistune is necessary to make the stock ECU work in a different chassis without ABS, TCS, etc. **And they actually provoke the CEL to come on by disconnecting the AFM, to prove that the globe hasn't been pulled!
×
×
  • Create New...