Jump to content
SAU Community

Recommended Posts

Thought I would write this up as I was struggling quite a bit with this one, and now have it down to a fine art.

Tools required: 1 x stubby phillips head, 1 x long thin phillips head.

OK so the story is I wanted to install some LED bulbs for the cluster and "piggy back" off the Oil Preasure guage wiring for a better gauge.

So here are the steps:

1. Unscrew the 6 screws under the steering column and drop it as low as it can go. Then pop of the top cover behind the steering wheel (see pic)

R34_cluster5.jpg

2. Unscrew the 2 screws at the top of the cluster surround

R34_cluster6.jpg

3. Pull the cluster surround out by pulling first a the top and then the bottom.

R34_cluster.jpg

4. Disconnect the Climate Control Sensor wiring clip and tube (REMEMBER TO PLUG THESE IN WHEN YOU PUT IT ALL BACK TOGETHER! OTHERWISE YOUR AC WILL BE EITHER HOT AS OR 18 DEGREES ONLY!)

R34_cluster1.jpg

5. Unscrew all the 3 screws holding the cluster in.

R34_cluster2.jpg

6. Disconnect the 3 wirring harnesses from behind the cluster. The one on the left is a particular bastard as the clip is located behind the accesable side of the plug. Not really much I can say here other than it is a real pain to get out. Once it is out I suggest destroying the clips on these so they can easily be removed in the future!

R34_cluster4.jpg

7. Finally pull the cluster out. The only way you can get it past the steering wheel is to the left as shown below.

R34_cluster3.jpg

Once the globes are changed, reverse the process to reinsert. I can now complete this process in about 10 minutes.

Link to comment
https://www.sau.com.au/forums/topic/237941-r34-cluster-removal/
Share on other sites

with the 3 gauges.

Step 1: get a flat head screw driver, stick it in the left side of the aircon (marked in picture in red), Then flick out the aircont vents, the whole thing should just pop out with the hazard light button.

edit-1.jpg

Step 2: after you have done that, there will be 2 screws holding the 3 gauges down. Undo them then you can lift up the 3 gauges all together with the cover.

Step 3: there will be 2 screws, one on each side, holding the gauges onto the cover. undo them and you'll be left with just the gauges.

Simple as.

  • 2 years later...
  • 3 weeks later...
  • 5 months later...

I highly recommend you use the one's that 666DAN has, i have in my car and couldn't be happier with the results.... :worship:

Do the 3 guages and the A/C screen too as they look awesome.

This is the dodgiest picture in the world but you get the idea - (Had sunlight shining in and i am a retard and moved)

post-47580-0-12161600-1326766871_thumb.jpg

  • 2 years later...

6. Disconnect the 3 wirring harnesses from behind the cluster. The one on the left is a particular bastard as the clip is located behind the accesable side of the plug. Not really much I can say here other than it is a real pain to get out. Once it is out I suggest destroying the clips on these so they can easily be removed in the future!

If you unplug the top plug first you can maneuver it so there is a large space on the right to get your hand or a flat screwdriver in and find the clip.

post-125345-0-40306400-1411864980_thumb.jpg

  • 4 months later...
  • 2 years later...

Hello,

I have the same problem as madman_rocks and radford23 : after replacing the bulbs by leds, and replaced the cluster in his place, the leds are working but my fuel gauge is not working anymore and stay at the bottom (but the empty light is still working). Also, I now have my handbrake light that always stays on. Any idea ? This is really frustrating...

Thx

  • 11 months later...
  • 2 months later...
  • 4 weeks later...
On 9/19/2018 at 8:06 PM, 666DAN said:

Update, I heard Marcus has been out of the LED game for quite some time. Sorry guys!

I have just changed my bulbs to LED. There's a problem. I have a series 2 dash so there is a orange film behind the gauges. Is there any way to make the gauges not appear yellow as I want them White 

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...