Jump to content
SAU Community

Recommended Posts

Car:

89 R32 GTR

Problem:

Misfire at idle and when i try to hold it at a certain amount of revs (e.g) 1500, 2000, 2700, etc etc., it idles at 1100-1200 rpm, and if i rev it to about 3000rpm and let my foot of it tries to stall on me. (1 out of every 3 times)

it revs up fine and boosts ok. but wont sit at any certain amount of revs.

tried:

coilpacks

plugs

cleaned/checked AFM

Replace coilpack wiring harness.

replaced all intercooler clamps etc.

any help would be great.

Link to comment
https://www.sau.com.au/forums/topic/239605-urgent-help-needed/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

where are the AFM's... likely too close to the comp housing.

Why you running all that stock gear with a T04Z anyhow? (and dont say 'running in' the motor)

i have 700cc injectors to go in, and plan to get a power fc, but i wont spend the coin on a power fc incase i need the cash to fix whats casuing the misfire.

so just want to get that sorted first.

don't think the afm's are too close if they were any further from the turbo they would be outside of the car. i can barely fit a thin hks filter between the afm's and the washer bottle and passenger headlight.

i just went and checked for error codes again and got: #21 (ignition signal system) my manual says: ignition signal is not generated continuously even though crank angle sensor is entered (dissconection between power transistor and control unit).

i check voltages to the coil packs and igniter but how do i check the sginal wire?

Check that the part where the CAS goes into isn't chewed out. It allows the CAS to flop around, and jumps timing up and down and causes mis fires mainly when attempting to hold revs constant.

fits snug in there..plus its held in by the 3 bolts

fits snug in there..plus its held in by the 3 bolts

no error codes anymore... #55 (all good).

the misfire became less when i fixed an injector plug up (was still missing). after driving it a bit the miss gets worse and it starts to idle at 1500 rpm again. and goes up and down from 1400-1500.

given up.

no error codes anymore... #55 (all good).

the misfire became less when i fixed an injector plug up (was still missing). after driving it a bit the miss gets worse and it starts to idle at 1500 rpm again. and goes up and down from 1400-1500.

given up.

when cold it idles at 1100rpm and doesn't miss... then about 30-40 seconds later it starts...the hotter it gets th worse it gets..

(sounds like dodgey coil-packs but i've changed them and they wouldn't make the revs rise to 1500rpm at idle)

anymore ideas?

STILL HAVE A MISSFIRE!!!

I have now done:

new plugs (3 sets)

coilpacks (3 sets)

new coilpack wiring harness

New injectors

New Power FC

New Z32 AFM's

Crank angle sensor

just check to make sure you have no vacum leaks. its along shot but start from there. correct me if i'm wrong but didn't you have a problem a couple of weeks ago with it not starting?

just check to make sure you have no vacum leaks. its along shot but start from there. correct me if i'm wrong but didn't you have a problem a couple of weeks ago with it not starting?

i have checked for vaccume leaks and also replaced all hose clamps... i wouldn't have thought that would cause it to missfire...

yeah i had trouble with it starting... had no power to coilpacks..(all sorted)

To save reading previous posts... this is where i'm at.

I need some more ideas please...

Problem: Missfire

What happends: runs fine for about 5-6minutes (only when started from dead cold, once its a little warm it missfires every start), then starts to missfire, if you give it a few revs and let the throttle off it dies for a split second and then the revs go up to 2000rpm (at idle) then slowly come back down to 1200rpm. (missfire the whole time)

replaced:

Igniter pack

Coilpacks

Plugs

Fuel regulator

Injectors

AFM

Replaced all hose clamps

checked all possible air leaks.

new power fc

new o2 sensors

New temp sensors

New ignition wiring harness.

the engine is fresh and has had all new gaskets fitted etc.

Any more help with this would be great. I'n my head i feel its a vaccume leak issue still... what else would cause the problems mentioned?

Edited by BNR 032

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...