Jump to content
SAU Community

R32 Turbo Sound Missing

heaveyfoot_ skyliner

By heaveyfoot_ skyliner,
in General Maintenance

 Share

Recommended Posts

tryandcatchme Collaborator

tryandcatchme

Posted
Posted

i lost my t/spool sound the other week,while playing with my vacuum lines,i swapped some around and found what ever i did it made my bov sound louder,but lost my spool sound,after changing over,it came back,so i found out that a change in the pressure can do wonders. Didnt notice change in power,turb still spooled over, not sure what damage etc in long run could have done,but it works how its supposed to so thats all im worried bout now

mad082 Grand Master

mad082

Posted
Posted

the only way a vaccum line can alter the spool sound is if it is making the wastegate stay open instead of closing (so exhaust air isn't making the turbo spool), and if that was the case you wouldn't have boost.

i'm guessing your spooling noise possibly isn't actually your spooling noise but a leak (such as bov not closing 100%) especially if what you did made the bov louder (you probably made the bov close properly).

what pod filter are you using?

  • 2 months later...
heaveyfoot_ skyliner Enthusiast

heaveyfoot_ skyliner

Posted
  • Author
Posted
the only way a vaccum line can alter the spool sound is if it is making the wastegate stay open instead of closing (so exhaust air isn't making the turbo spool), and if that was the case you wouldn't have boost.

i'm guessing your spooling noise possibly isn't actually your spooling noise but a leak (such as bov not closing 100%) especially if what you did made the bov louder (you probably made the bov close properly).

what pod filter are you using?

hi mate thnks for the reply

its got no pod filter

one more question thing they say its a faulty turbo so is it ok if keep driving the r32 ? or is there any option to remove the turbo and drive it without the turbo like non turbo or fit a new non turbo engine in the car

BeEnAr Experienced

BeEnAr

Posted
Posted

Hey mate don't listen to all the people putting you down.

Just take your working/stuffed turbo off and fit one of these suckers!!

post-50346-1232350147_thumb.jpg

1. Improved fuel economy

2. Instant increase in engine power?

3. Reduction in carbon accumulation to your engine

4.Minimized air pollution

5.Enhanced throttle response and acceleration

6.Easy to install,DIY.

post-50346-1232350230_thumb.jpg

Super Spiral Turbo Ventilator creates a vortex air flow to imporve air & fuel mixture? enhancing your engine's performance.It reduces the carbon accumulation in the engine and substantially increases the horsepower to your engine.

Super Spiral Turbo Ventilator blades are made of advanced precision bearing technology (running up to 30,000RPM). Yep The blades are made out of bearing technology!!

Aluminum alloy gravity diecasting design is not only anti-rust, but also has the ability to match your high-revving engine. The blades have special angles to promote extra air flow to the inlet manifold and assist in providing better engine combustion. Experience strong torque during low to medium RPM ranges but also extreme horsepower at higher engine revolutions.

Furthermore, it is environment friendly and greatly increases performance efficiency.

The products can be installed to gasoline & diesel cars, as long as there is

the inlet pipe on the air inlet of the throttle.

HAHAHAHAHA!!!!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I am probably calling this too early but I think I found what part of my problem is. I have a couple of dents that are fairly close to each other and I tried to fix them individually. Recently I put one larger coat across all the dents and sanded it and for the first time ever it's all even except for the edge where the bare metal is, I just need to put some putty there. I'm ordering some better longer blocks that are more flexible. Other good news is that the other repairs on my panel are flat even with the guidecoat. It's these 2 dents which are an absolute c*nt l lol.
    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      Murray will have better input, but I'd be going with less filler, and aimed at the low spots mainly, and hence won't need as much sanding, which then means get the guide coat on earlier. That's how I'd do it, BUT, I'm not a pro, I'm a DIY hack who will then get the shits halfway through, and have one spot awesomely repaired, and the other spots look like a 3 year old was left unsupervised with workshop tools...
    • timmy94
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By timmy94 · Posted

      Where is the most common place to locate it? Disappointing that Garrett won’t make a fitting for it since they know everyone will use it
    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That's the spirit.
    • GTSBoy
      R32 GTR Limp Mode?

      By GTSBoy · Posted

      A HICAS fault really should not cause the engine to go into limp mode. These cars are so old that the systems barely talk to one another. The thump might be the lockoff solenoid valve for the HICAS (the safety valve) getting closed, to lock the rear wheels "straight". I say "straight", because when my HICAS used to shit itself before I took off and nuked it from orbit, it would lock up with the rear wheels wildy non-straight and you'd need 45° of steering wheel to drive straight. Take off and nuke it from orbit. First step is to pull the smaller of the two plugs out of the HICAS CU. See if it stops misbehaving. You can also (whilst leaving it plugged in) try to get the HICAS CU into diagnostic mode by doing the pedal dance, or by connecting a CONSULT capable diagnostic reader into the car and seeing what it has to say for itself. Can't do either of these with it unplugged though. 1st gen HICAS is a ballache. I would do a complete delete. I did do a complete delete.
×
×
  • Create New...