Jump to content
SAU Community

Group Buy: R33 Gtst And R34 Gtt Cold Air Box Cover


Recommended Posts

  • Replies 211
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

would also like to know due to christmas funds increasing :P

R33 GTST S1 with stock cooler piping holes

Edited by auss13

have recvd 4 payments so far. details of transaction hasnt been updated yet so but have recvd pms from those who has made the payments. ill be sending some out tomorrow once my accounts updated showing whose payments has come in.

also these will be coming in as a registered post.

ta

Ash

also another quick note

for R34 ppl i apologize but i over looked the AC condenser so a small alteration will need to be made to install the box. i did mine last night and its not hard at all and that side cannot be seen. all that needs to be done is a small section prop 5cmX5cm to be cut out. other then that it fits nicely. ill post up a pic of the install and how much an where needs to be cut.

for R33 ppl these are a straight bolt on.

sorry guys but i dont know how i over looked this.

here is a pic of my install.

it was a very quick 15min job and sorry about the pic.

iv also attached a pic of the piece i had to cut out.

again i apologize for looking over this but as you can see its a very small thing.

installed in my R34 GTT

24122008057.jpg

24122008058.jpg

24122008059.jpg

you can see here the bit i had to cut to make way for the AC condenser

24122008060.jpg

the size of the plastic cut out

24122008061.jpg

and here is a side pic of the box. the red square is what needs to be cut out

P021108_1318-1.jpg

Too easy mate :santa: Say when you want to check your radiator overflow bottle is it hard?

nope

the top lid is held in by 3 allen bolts. just undo that the top cober comes off and presto you AFM, pod and radaitor bottle is there

also howie and MR XTC i got your payments today tomorrow im sending them off YAY

lol

Yay me and howie are first neh neh :)

lols!

hopefully i can get it before NYE or else party organisation is gonna' take up most my time.

No more defects booyeah!

Greatest investment to date :devil:

MRXTCZ

lol

money is in just the transaction details hasnt been updated to tell where the cash came from.

eMsta might have an extra box left over so ill let ya know soon along with others that have sent me pms.

any chance for me getting one i can send payment or pick it up any time really would love one of these

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...