Jump to content
SAU Community

Recommended Posts

Alright, this will be my next projec tonce I get my S15 RB26DETT up and running but as for now I am already acquiring some parts, namely the damaged RB26DETT engine. I have done a bit of searching and people are saying that you need to machine the headstud holes and retap, some others also said you can use the RB25DE headstuds and they work proper, can someone clarify. What else needs to be done, was thinking about a new headgasket and a baffle and the usual RB26 headwork for oiling problems. Can anyone advise me who has done it as I am thinking along this direction. If the damaged engine has a good block and crank then my swap will be an RB26 but not sure until it is scrapped, guy just told me it was a spun bearing and the crank needs polishing but no one can know unless it is scrapped. Let me know what is needed as I am thinking along these lines.

Good question that , non VVT head on VVT block - if the 26 block is RS .

I suppose you could look for an R32 RB25DE block and fit it with piston oil squirters and good internals .

I think American mobs can sell you non metric threaded fasteners but you have to get the block drilled/threaded and not sure about the heads bolt holes .

Ask SK , cheers A .

  • 3 weeks later...

What exactly do you want to know? The head will bolt on using rb25 head bolts, but as i said the compression ratio will be low due to the difference in cylinder volume. You really aren't gaining anything by using a neo bottom end, as a non-neo bottom end will end up with a more appropriate comp ratio. You could get a set of non-neo forged pistons and fit them to the neo bottom end, that will fix the comp issue.

Okay are you sure that using the RB25 headbolts I can bolt on the head? The reason I am using the Neo bottom end is because the RB26 engine that I am getting has bottom end damage and that I already have an RB25DET Neo engine in my GTT. Maybe the RB25 forged pistons may be an option I can look at, thanks. I just want to confirm that the headstuds from the RB25 can work on the RB26 head without worries, can you confirm firsthand?

I wanted the individual throttles and also the intake mani run on the side for shorter coldside piping, and also maybe do a twin turbo setup all at the same time, oh and the wow factor :/. Actually I am getting the RB26 for a good price and getting aftermarket intake manis for the RB25DET Neo is harder and expensive along with the harder to get injectors and then the exhaust manifold. Okay so RB25DE or is it RB25DET headstuds or are they the same, gonna do a search now?

Yes I know but I am getting the entire head for a good price and having the individual throttles is an added bonus as well as the twin turbo setup. Let's not harp on the topic I just want to make sure you can use RB25 headstuds and if so is the RB25DE and DET headstuds the same, I am thinking so. Thanks to all for the input BTW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...