Jump to content
SAU Community

Recommended Posts

Had a quick search and couldn't seem to find an exact answer to this.

Just took the head off from the RB25 and figured i'd clean all the carbon build up on the tops of the pistons while the heads away. What's the best thing that will dissolve/clean away all the carbon? Metho? Kero? I have no idea...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/247044-cleaning-carbon-build-up-on-pistons/
Share on other sites

A soft aluminium scrapper, and sometimes a small screwdriver used as a peen tool and the carbon pings off [don't use it too hard, the idea is to shatter the carbon not mark the piston]. Used correctly both tools will remove carbon without damage. Then your stuck with carbon soot falling down between the piston and the bore and sitting on the top compression ring, but it shouldn't last long once you start it up again.

I've heard Water Meth Injection will do the job nicely..

Haha i was actually thinking then when i saw how much crap there was on top of the pistons.

Ill try some of the suggestions, thanks a lot guys.

becareful not to go too silly, if the engine has some kays on it and you get aggressive and dissolve the carbon build up around the ring (lands, etc) etc it will blow smoke......

Edited by URAS

Oh ok, cheers Trent. Im getting the head done at that Lewis engines place that you mentioned in Adelaide, see how it goes. You end up getting a head off of them?

Edited by PM-R33
Oh ok, cheers Trent. Im getting the head done at that Lewis engines place that you mentioned in Adelaide, see how it goes. You end up getting a head off of them?

im building a pretty crazy 26 atm for a customer so i should be sending one over there (mine) to test the waters first in about a fortnight or so..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...