Jump to content
SAU Community

Recommended Posts

Guys, I need your advices, I have a R33 gts-t, I found it's quite scary to drive in the wet sometimes, the car starts to "Drift" when I take off in first gear to make a turn, sometimes in a hurry right turn, I feel i'm going to lose control and spin around.

have u guys experienced the same problem??? My car only has some basic mods, FMIC, turboback exhaust, CAI, standard turbo, and most of the time I run stock boost, so there is not a lot of power. I have Buddyclub N+ coilover suspension and the R34 Gtr wheels fitted, tyres are Dunlop lemans, few months old. In a sunny day, it's fine, only happens in wet.

Yeah !! I have the same issues, on wet roads, I think it's due to hard suspension. I got EDFC setup in my car and I noticed that harder the suspension I set, less grip on wet roads I get. So I always drive on softest setting on wet and just have to be very careful. I try to drive without the turbo kicking in (slow launch)

Yeah !! I have the same issues, on wet roads, I think it's due to hard suspension. I got EDFC setup in my car and I noticed that harder the suspension I set, less grip on wet roads I get. So I always drive on softest setting on wet and just have to be very careful. I try to drive without the turbo kicking in (slow launch)

Which Tein have you got??? Super street??? I set my Buddyclub N+ to softest, and it's still happened

what tyres are you running? hows the wear on them? how low is your rears, how much camber does it have? When i put my tiens on they lowered the car and gave me a fair amount of camber front and rear. the extra camber on the rear created uneven tyrewear on the inside of my tires and I could easily break traction when turning in first say to do a U or 3 point turn. It got to the point where it was quite predictable. Would also break traction in the rain on red lights if i gave it say 1.5k revs on take off.

I now have a set of good Yokos and camber kits so it doesnt do it anymore.

what tyres are you running? hows the wear on them? how low is your rears, how much camber does it have? When i put my tiens on they lowered the car and gave me a fair amount of camber front and rear. the extra camber on the rear created uneven tyrewear on the inside of my tires and I could easily break traction when turning in first say to do a U or 3 point turn. It got to the point where it was quite predictable. Would also break traction in the rain on red lights if i gave it say 1.5k revs on take off.

I now have a set of good Yokos and camber kits so it doesnt do it anymore.

Thanks for your reply, very helpful info.

Tyres are Dunlop lemans, about 3000kms old. rear is about 340mm center of wheel to guard. I don't have the camber kits, so I guess I need the camber kits to fix the problem.

I found it's quite scary to drive in the wet sometimes, the car starts to "Drift" when I take off in first gear to make a turn, sometimes in a hurry right turn

Don't hurry then. Slow and deliberate.

R34 Gtr wheels fitted, tyres are Dunlop lemans, few months old. In a sunny day, it's fine, only happens in wet.

Everyone else has covered most of it on the tyre side, so my only other suggestion is to set the suspension up to understeer as much as possible. If it rains set the rear dampers to full soft and the fronts to full hard. If the ride's a bit too harsh in the front dial it back little by little, but always ensure the fronts are a lot stiffer than the rear.

Which Tein have you got??? Super street??? I set my Buddyclub N+ to softest, and it's still happened

I'm not sure what Tein they are , coz I got them with the import, didn't bother to chech back then and didn't have much knowledge either.

It is called drving normally. It requires throttle modulation rather then just floorg it :yes:

I agree with Roy, even a stock skyline would lose traction on wet conditions. The mods make it worse (but perfect for dry conditions). So I guess there’s nothing we can do about driving when wet other than just been very careful and always keep in mind that your car is designed and moded to suit dry conditions.

Just go easy on the gas when wet.. nothing wrong with the car… J

It is called drving normally. It requires throttle modulation rather then just floorg it :P

I drive very slow on road, most of the time with the boost controller is switched off, but it still loses traction in first gear in the rain

short shift into 2nd as soon as you get rolling

fix the camber in the rear that's the main thing (I also suspect your suspension is too hard)

dunno what else to tell you, mine just grips in the wet, the rears only spin if I want them to... and that's with 260rwkw and 2way mech diff... some pineapples set to squat might help as well

when I first got the car I had hard springs in with worn standard shocks and crappy federal tyres and the thing was pretty lethal in the wet... totally different car nowadays

It is called drving normally. It requires throttle modulation rather then just floorg it :D

ZING

i can break traction in 3rd in the excel when its wet......

its all about the right foot

+1 on throttle control.

My car is stock power wise on 255 Federal 595SSs, and in the wet it is very easy to get the rears spinning, even on fresh tyres. I manage to keep traction though by keeping the revs below 2,500 rpm (even taking off from lights in 2nd) and taking it easy around corners.

It is all about driving to the conditions.

If you really can't do this, get a piece of plastic and block about 3/4 of your air filter. The resulting restriction should bring the power down so you will get no wheel spin at all :spank:

I don't have issues with traction in the wet with a fair amount of throttle, too much throttle and you lose it but I do have AWD...

How *much* power are you putting down? With how much accelerator?

You could have badly setup suspension OR bad tyres, or you could just be overestimating your car, most cars with a good LSD get sideways in the wet with heavy acceleration, but it's hard to tell on a forum what exactly is going on.

There are some serious topics on getting power down somewhere here (as in suspension, not about right-foot control :spank:)

EDIT: Oh, on corners, it could be suspension setup or it could be overestimation of the car's handling. What rating are the springs of your suspension?

And Dunlop LeMans are *ok* in the wet, not the best, I have them as well, the fact that you have 18inch rims on a GTST also means much lower profile so that's probably not going to help.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...