Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yep - Morgan and Caterham are imported by the same guy.

He has an Aero 8 series 2 as a demo (see attached)

The Aero Max is a bit cooler, but non in Aus. They are quite expensive for what they are - I still think a nicely done Cobra replica would be a better car.

post-936-1230687508_thumb.jpg

post-936-1230687523_thumb.jpg

James,

just wondering the sticker price on the Maserati GranTurismo? GF's old man is apparently looking to trade up from his 3200GT(A) and im curious to know how much they go for (without being rude and asking him of course lol)

Hi all - I'm trying to plan my fleet for the new year.

Of the existing machines... Some cars are great and will stay, some cars are great but should probably be refreshed, some cars aren't that great and some are great in my eyes - but just never get used. Following is a list in order of category. I need to keep the total number to around 26.

Group 5

Aston DB9 Volante Sell

Aston DB9 Coupe

Ferrari 360 CS

Ferrari F430 Spider

Ford GT

Lamborghini Gallardo Spyder Refresh, maybe even get a white one?

Lamborghini Gallardo Superleggera

Group 4

Audi R8

Audi R8 R-Tronic

Bentley Continental GT

Maserati GranTurismo

Mercedes AMG CLK 63 Black Series

Porsche GT3 Chip and exhaust?

Group 3

Maserati Quattroporte

Aston Martin Vantage

Group 2

BMW M3

Audi RS4 Avant

Hummer H2

Group 1

Ariel Atom 2

Lotus Exige S

Mitsubishi Evolution X MR

Audi Q7 S-Line

-

Rules:

Must be available in Australia - so no Alfa 8C

Must be a current model (within reason) - so no Countach

Must be 'affordable' - so no Zonda F

I'm after ideas on great cars - not complete lists. Things like a Continental GTC and Aston DBS are in the works - and a GTR is a given.

But what are we missing? What is cool that you can get in Aus that people would like?

Happy to hear your thoughts!

J

This is a hard question as you've already got most of the best cars on the market :(

In addition to the italics above;

-New M5

-Ultima GTR spyder, they call it a "can am" (pretty sure they're still available in Aus, we have one at work thats aus delivered which is a 5.7L with an HKS turbo hanging off the side)

-The latest sl from merc, SL55's or SL63's arent too badly priced, although some members may have those already

-997 Turbo/Cab, would be nice to have a droptop porka floating around. Didnt you have a Turbo a while back?

-Dodge Viper, if there's someone bringing them in

-Would love to see a 997 GT2 but its a bit pricey, unless maybe an Aston gets sold...

-GT3 RS. Great addition to the white one and rare as hens teeth but not too expensive

-Ferrari California. I think its quite ugly personally but as its the new Italian on the block maybe the members would like it

-E55 AMG. Along the same lines as the white Masa

Thats all i can think of :(

And an R36 Wagon :action-smiley-069:

I hear you on the R36, but not sure it would fit the image of the company.

It's a well-sub-$100K ride and if I was paying $36k pa, well... life's too short.

It would be more viable to test-drive one at the dealers and pay for the privelge of the top shelf stuff.

Edited by Mean_R34

James out of curiosity how much is it going to be to bring in a Challenger and get it on the road?

Will you be bringing in one of the special editions or the standard one? ie. the drag race model or the Targa model (or is the Targa from a 3rd party source?)

I hear you on the R36, but not sure it would fit the image of the company.

It's a well-sub-$100K ride and if I was paying $36k pa, well... life's too short.

It would be more viable to test-drive one at the dealers and pay for the privelge of the top shelf stuff.

You have to remember the way the Club works is that different level cars are worth different point values. So using an R36 would costs bugger all points wise compared to the ferrari F430 Spyder. Price wise the R36 is the same as the EVO X (if not slightly dearer for a fully specc'd one) but it falls into the Group 1 cars - which they have bugger all of for use on the roads - and yet has some usefullness that you don't get with a Lotus or Atom, and I can tell you is suprisingly fun to drive. Remember the R36 is the fastest production car VW has ever produced!

So if a member wanted to take the wife and kids away for the weekend the R36 wagon would be one of the few cars the club would have that would allow them to fit everyone plus luggage, prams etc into the car and yet be a damn sight more fun than their 4WD tractor they no doubt already own. I bet it would get more use than James stupid ugly Q7.

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...