Jump to content
SAU Community

Recommended Posts

  • Replies 181
  • Created
  • Last Reply

Top Posters In This Topic

NEW ENTRY FORM

MUCH EASIER TO UNDERSTAND TOO

http://members.iinet.net.au/~gavingriffith...tryform2010.pdf

Just to be aware folks, there was a typo which I did not spot until late last night on the original form that I was given to begin redesigning it from (You can blame me for any problems) If you look, the two images from my photobucket account above that Matty has linked to show the wrong end date. This has been corrected in the PDF link but I will not be able to do anything about the photobucket ones until tonight when I get home. Any entries coming in from the JPG images with and end date of the 14th will still be accepted but I suggest using the PDF link, it will print more clearly in any case.

There are also some pricing differences in there in the way things are grouped together. Nothing is more expensive than before and most "Packs" are a couple of dollars cheaper than the previous prices combined. That is to say it is slightly cheaper to enter with a full event pack than it is to enter the sprint and the show and shine and to buy a dinner ticket and promo pack seperately.

Paul.

EDIT, SemislickR32. No, if you have entered on the old form you do not need to enter again.

Edited by Blue

OK, photobucket fixed. I re uploaded them with the same file names so the forms are still in Matty's post. This entry form is now uploaded on the Skyline nationals website so people should be seeing the same form from any current place to get them.

I suggest using the form direct from the nationals website so that if any further changes are made you get the current form. I do not expect the form to change between now and the event though.

http://skylinenationals.com/2010_Skyline_N..._form-final.pdf

Sent (and paid ) my forms off 4 months ago and emailed again 3 weeks ago and no reply :mad:

who did you email? I sent one through today and got a reply 3 hours later. Email was sent to : [email protected] (via the skylines national website)

Just to confirm, any model vehicle is welcome to enter the super sprint at Mallala. There is also 4 different groups, standard non turbo, standard turbo, modified turbo and 100% track car group etc.

Ryan

who did you email? I sent one through today and got a reply 3 hours later. Email was sent to : [email protected] (via the skylines national website)

Just to confirm, any model vehicle is welcome to enter the super sprint at Mallala. There is also 4 different groups, standard non turbo, standard turbo, modified turbo and 100% track car group etc.

Ryan

They have the cash , just to slack to send a reply
So what is the likely timetable and format for the track day? Time attack or racing

The exact format of the day is being settled but things should start to happen on the track itself by 10:00 with scrutineering starting at your normal sort of 08:20. Supp regs and formal sprint entry forms should be gong out very shortly to those who have already entered the sprint on the main nationals entry form.

The day will be a multi car supersprint format against the clock, not racing. Racing would exclude almost everyone who would want to enter as that would require a C level license not an L2S.

OK, I should have Rbware sorted now, if anyone else has missed out on an entry confirmation could they PM me about it so I can follow it up?

REV-031, if you want to do it, just do it! There is no pressure at this type of event to go any harder than you want to, so if you just want to cruise around at a moderate pace and get a taste for it then there is nothing to stop you doing that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...