Jump to content
SAU Community

Recommended Posts

it was a great night, my 1st of hopefuly many :rolleyes:

put my car on the dyno, to see what my base figure is and to check its tune

got 123.8kW with only a Pod and 3" catback

i was car #21 the white 180sx

here are the graphs

post-59633-1234567940_thumb.jpg

post-59633-1234567999_thumb.jpg

  • Replies 152
  • Created
  • Last Reply

Top Posters In This Topic

When the cops set up the "block" I promptly went down and chatted to them. They understood perfectly well that it was for charity and as long as there were no heroes, then it'd be fine for them. We relayed this message to everyone inside and I'm gonna hope for now that the s14 was either f**king about or just had bad luck.

OH NOES! www.fmylife.com , go contribute.

The cops were cool, we never have problems at R.E nights. Like anything, there are good and bad.

It doesn't help when everyone on the street piss bolts over to crowd around when shits going down, yeah! lets make the dudes with the power feel intimidated!!

On that note, thank you sincerely for attending, people.

It's a long night for all involved and we appreciate it all.

CFA, Red Cross and Wildlife Victoria thank you as well.

Till next time mofos!

P.S Also, that white 34 GT-T, sleepy much?

P.P.S Ruffels, it'd be nice to get a thank you for, ya know, finding your wallet. :rolleyes:

hey mate how did u end up going with the stickers? haha 310 for the gtt yeh? spoke to u bout getting my s14 done at sams when its ready.

good to see Ruffels stock 33 make 160.4 on stock boost and Hekt1k made 156.4 on stock boost also no mods bar exhaust

just got back. cops are loving it. there all over the joint.

both sides of the service lane. couple down center road. princess hwy, and i bet westal.

I think I left at the right time then.

Was a really good night, as always. Thanks Matt!

OH NOES! www.fmylife.com , go contribute.

LOL that site is funny:

"Today, I texted this girl I really like and she didn't answer. She did about two hours later and it said "sorry I was having sex at the time you texted me. So how are you?" FML"
Hahaha nah too much effort!

Tell Donny to bring the NUR r34 gtr or even the nismo bayside blue 34 gtr! :rolleyes:

See ya tonight man.

Liam.

Yeah Liam, Tim (not Donny, LOL!) bought the R34 GTR V-Spec II Nur along but he was car number 53 inline and when he arrived they were only up to car number 30.

He had to leave and could not wait. It would be good to see if it still pulls 306 rwkW's like last year at RE Customs.

Tried finding you last night... I should have just called you... You still got same number?

Some nice cars there last night, a lot of EVO's too.

Jamie - sorry I couldn't find you to say goodbye last night.

Hey Julliet!

Yeah thats cool, I went to the car park to see if you were still around. I left around 11:30pm.

Anyway as long as we all got home without any issues its all good!

BTW I had a chat to a group of NissanSilvia fellas, they are a funny / silly bunch LOL! One of them wanted to go into Club Eight to have a "Poke" at $120 for 30mins LOL!

We all deared him. Was funny and staring at the guys walking out of the place...

lol be pretty funny if we all went down there to Club Eight and took a number and sat and waited.

might need to call in the casual's to do the overtime.

i got a strange stare from three coppers standing next to there cars on center road as i went past. might of be a 'thats a loud volvo face'.

what i found amusing was this group of about 4 odd looking dudes, when i was backing my car up heard the convo go like "is that a liberty ? looks like a toyota, ... nah man its is a liberty"

any one know what PROEVO put out ? last i saw it had no cooler, had some kind of Cold air ice box thing

lol be pretty funny if we all went down there to Club Eight and took a number and sat and waited.

might need to call in the casual's to do the overtime.

i got a strange stare from three coppers standing next to there cars on center road as i went past. might of be a 'thats a loud volvo face'.

what i found amusing was this group of about 4 odd looking dudes, when i was backing my car up heard the convo go like "is that a liberty ? looks like a toyota, ... nah man its is a liberty"

any one know what PROEVO put out ? last i saw it had no cooler, had some kind of Cold air ice box thing

Did you go for a run? I saw your car parked but didn't see it going in?

Yeah Liam, Tim (not Donny, LOL!) bought the R34 GTR V-Spec II Nur along but he was car number 53 inline and when he arrived they were only up to car number 30.

He had to leave and could not wait. It would be good to see if it still pulls 306 rwkW's like last year at RE Customs.

Tried finding you last night... I should have just called you... You still got same number?

Some nice cars there last night, a lot of EVO's too.

Ah yeah thats right tim hahaha

I only stayed for an hour as I had something on later in the night, some bloody nice cars there! there was a midnight purple 32 gtr that looked absolutley mint!!

pm me your number jamie. I went swimming in a pool with my phone still in my pocket and it drowned haha

Did you go for a run? I saw your car parked but didn't see it going in?

yeah i went one around 12.30am

got 132kw with airbox, and a really rough line.

last time 140.2kw with pod and a very smooth line.

think i know what will fix the problem, high flow my turbo , piggy back Greedy unit, fuel pump, and shift kit, and a few other bits

should smooth out that line (anything for an excuse) :domokun::)

any one know what PROEVO put out ? last i saw it had no cooler, had some kind of Cold air ice box thing

282 I believe...

Good night, well done to all the boys at RE for putting on a great event as usual, with another massive turnout, and Matt on the BBQ :domokun:

yeah i went one around 12.30am

got 132kw with airbox, and a really rough line.

last time 140.2kw with pod and a very smooth line.

think i know what will fix the problem, high flow my turbo , piggy back Greedy unit, fuel pump, and shift kit, and a few other bits

should smooth out that line (anything for an excuse) :domokun::)

what mods? got 10kw on me, i had full exhaust and thats it last night, installed FMIC today, still need to get my EBC on...

Ryan, Full exhaust . . .FMIC . . High flow panel. mines a series 2, is your 97 series 1 or 2 ?

Was a great turnout. We had 75 cars...finished 3:00am

damn im tired...we've raised $3240 for the bushfire appeal.

PROEVO - i still haven't finished tuning it....atm its 290 @ all 4s, 17 psi we'll be pushing to 25 - 27 psi.

Top stuff Ray. :domokun:

encore ??

Ryan, Full exhaust . . .FMIC . . High flow panel. mines a series 2, is your 97 series 1 or 2 ?

Top stuff Ray. :domokun:

encore ??

s1

was the filthy silver one, #22... hit speed cut in 4th, and was climbing, and hit 134 on kickdown, so with the fmic fitted, it should be close to yours... will re-run when i wire in the EBC, cast just makes life hard haha

ah series one.

well its already has less power at the flywheel to start with, then through the drivetrain and four wheels lost more again.

but yeah just making the whole thing breath alot better is a good shot. its yours a stealth cooler ? or are you going to cut the hole under the battery ?

and yeah i was paying for mine as yours was backing up to the dyno, didnt make it out in time to see it. good that you rocked up though :domokun:

ah series one.

well its already has less power at the flywheel to start with, then through the drivetrain and four wheels lost more again.

but yeah just making the whole thing breath alot better is a good shot. its yours a stealth cooler ? or are you going to cut the hole under the battery ?

and yeah i was paying for mine as yours was backing up to the dyno, didnt make it out in time to see it. good that you rocked up though :(

yeah, thought it would be pretty similar til boost goes up as i had a series 2 cooler on it... turns out larger rear housing did more than i thought :P did you hit speed cut?

got the JJR stealth, PITA to fit, get a blitz!!!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...