Jump to content
SAU Community

Recommended Posts

KING87 - what's the power difference between 23psi and 25psi on your car? i'm contemplating pushing mine a little harder.
and my 2c on the question of the thread - buy the -5's. I've never met someone that doesn't want to chase more power in the future. Buy bigger now for the bigger/longer term picture.

Edited by tk80

Under 300kw on a stock engine would be a good buffer. I was only running 325awkw when it let go. But then again I had a 89 gtr so the engine had a long life.

+1

It's safe and still got some pull when you need it!

understatement......I have deep reservations about that engine's longevity at that power / boost level ......I sure as hell would not want to be in the car when she goes BANG!

Yeah, know the feel!

As long as you know what to expect and be prepared fork out the cash.

Then just keep driving and enjoy it as it is.

KING87 - what's the power difference between 23psi and 25psi on your car? i'm contemplating pushing mine a little harder.

and my 2c on the question of the thread - buy the -5's. I've never met someone that doesn't want to chase more power in the future. Buy bigger now for the bigger/longer term picture.

Agreed.

Yeah I know what to expect and I will keep you all posted if and when it does let go.

Not sure what it made on 23psi it's got 25 @ 5000 RPM I will try dig up the dyno print out.

-5's for the win for street and track but agreed they could use a few more cubes behind them

On the street.

Ahh this has pushed me to get -5s now.. With a built engine (forged pistons, rods, cams etc) and on e85.. What would be the power difference from 9s to 5s?

And the difference on hitting full boost would be from 4.5k for 9s and 5k for 5s?

Ahh this has pushed me to get -5s now.. With a built engine (forged pistons, rods, cams etc) and on e85.. What would be the power difference from 9s to 5s?

And the difference on hitting full boost would be from 4.5k for 9s and 5k for 5s?

Lower than that for both but remember boost is not a switch things happen way before full boost. And your producing the same power as -7s with- 5s way before full boost all the way to 7.5k and then when you change gears your always in the sweet spot. But as I said drive both and see what you like and then make your decision. Any reputable rb workshop will allow you to experience multiple setups they build if they see your serious.

understatement......I have deep reservations about that engine's longevity at that power / boost level ......I sure as hell would not want to be in the car when she goes BANG!

Good excuse to build a real engine :)

Ants wrote; ...I sure as hell would not want to be in the car when she goes BANG!

Ha ha the best. I was driving around with a spun bearing for 5 months until it eventually went bang. Last 2 months it sounded like a tractor. As soon as I heard the bearing a put slick50 in it and it lasted for 5 months. Everyone was shocked including me ha ha.

Used to drive 50 kms a day on the ring road carpark and other drivers used to look in amazement at the knocking sound coming from my 33.

Edited by XGTRX

How was the crank when you pulled it out? Lol

When it totally gave way it was like rattling a can of bolts. luckily it happened in the driveway and I switched it off straight away.

When my engine builder took the sump off to send it off for the extension he just shook his head. The 4th piston bearing was dislodged, rod was free and piston was wedged in the bore. There was more metal in the sump than oil. Ha ha classic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I am getting the same issue. Did you resolve it? I just got it after installing my new super coppermix and literally the same issue, new fork, new 18mm carrier, release bearing that came with the kit and replicated the exact same sound. 
    • If you like - I have the STL files so I can email em. There's a couple of gotchas (i.e the holes are not threaded so you might need/will need) to utilize some M3 melt-in threads for some of the points. However if you want to be super accurate, and are willing to remove your calipers and your SHOCKS it's a really good tool. You also might need to scale the part that measures the tyre width a bit wider. It defaults to a 7.5in tyre and I mean who is running that. Luckily with the magic of CAD this is very easy to rescale.
    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
×
×
  • Create New...