Jump to content
SAU Community

Tricks To Get Into Evil Driveways With A Lowered Car

vidospace
 Share

Recommended Posts

vidospace Mentor

vidospace

Posted
Posted

OK so I stupidly went out and got a hot looking front bar for my R34 before getting my suspension done. The bar scrapes just a touch on my drive way no matter how I seem to turn the wheel. Once I was able to get in without scraping but I cant figure out what I did right! Now my car is back from the shop getting the SK kit fitted and it will be lower again (not by much but maybe 1 inch). The drive way is a dip basically. Our road is curved in the centre and then the drive way banks up over the pavement before flattening out in our property. So you can see my issue. Over speed bumps I know to go at an angle and all is fine but I need to know how to go at an angle and then when to turn back straight or opposite to get over such dips without killing my kit? Suggestions?

If worst comes to worst I might need to install a metal grill between the road and the drive way to even out the angle. But that might be overkill!

some_cs_student Veteran

some_cs_student

Posted
Posted

I have a very steep driveway so here's how I get in / out, but its only possible because my driveway is really wide, it can fit two cars side by side (nearly :yes:).

On the way out: drive onto the nature strip, reverse back on a sharp angle to stick the rear towards the road, then change it the other way full lock, I often do drive a little onto the other side of the kerb because the rear of the car is high enough off the ground. Sometimes forwards / backwards one more time to get the angle right and then gently across the road and it just makes it.

Getting in, completely different, I drive on the wrong side of the road because one side of the driveway is less steep then the other, turn late and sharp and the bar *just* makes it (and I"m heading straight for the wall so I stop, I then reverse and go in the 2nd turn :)

Every driveway is different, I've seen a few people make ramps (usually illegal under council law) and someone who had a WRX had a "cross over" built by his council (cost some serious $$$), another person got a free cross over made because she was near a council that did it for free :)

Personally I'm really tempted to pull out a ramp and drive onto it and take it away afterward.

Oh how lows your car? My one was 8cm from the ground when I put the Japanese suspension in, raised it to 13.5 and now its about 11.5 or 10.5 at the front bar...

Good luck!

bt23 Enthusiast

bt23

Posted
Posted

My one is pretty much sitting 10cm at the front and sides but the shape of my front bar sticks out at the lip which caused me a lot of grief during my first couple months owning the car (I had to eventually get it re-fiberglassed + resprayed). I still occasionally sand the paint underneath from scraping some driveways but nothing too drastic.

I live in a cul-de-sac with a very steep curb but mastered it by just keeping in mind to take a big angle. For some of the driveways with dips, you could also try reversing in. Some driveways you may just have to completely avoid altogether. It's just part of having a lowered car.

Hang in there...

P.S. There is no shame in getting a mate to step outside and check as you attempt to drive up. Sure, onlookers might think you are a wank, but at the end of the day you are saving unnecessary stress and money!

Phobic Collaborator

Phobic

Posted
Posted

just smash it up there and keep repairing the bumper haha, nah the best way is just go up it at an almost parrallel angle it helps when you have wide wheels that stick out the guards because they go up the curb before the bumper hits

vidospace Mentor

vidospace

Posted
  • Author
Posted

Well guys, got the car back today. Its about 1cm lower than it was before (just purrrrfect), and low and behold, it doesnt scrape AT ALL!

Guess the lower back end and harder suspension helped!

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted

i have the worst driveway in aust...an extremely steep twisting item that i have to put the Jeep in 4wd to reverse it up.

thats why i have a high ride height drag car not a gutter scraping circuit item.

some_cs_student Veteran

some_cs_student

Posted
Posted

Dirtgarage, that driveway sounds dangerous, for any non-4WD on my driveway you can't attempt to drive straight in without angle to you hear a scraping sound (in stock cars its often the rear).

videospace, glad to hear you got it in, I ended up getting my bar re-fiberglassed and re-sprayed and I've been very very careful since then...it wasn't really bad damage but enough scratches to get to me :)

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
just smash it up there and keep repairing the bumper haha, nah the best way is just go up it at an almost parrallel angle it helps when you have wide wheels that stick out the guards because they go up the curb before the bumper hits

not if you run stretched tyres tho :)

Pezhead Grand Master

Pezhead

Posted
Posted

Have a look at the gutter and slope of the road. I put a thick board in the gutter and that gave me the 1" I needed to clear when leaving. Roads are purposely crowned to drain the water away to the gutters. For me the clearance problem was simply coming off the lip of the driveway into the gutter. That 1" drop caused the bar to drop down onto the slope of the road.

I got some 2" x 12" from the lumber store and put two sections out on the road.

I worked pretty well until the first big rain - I live on a hill.

Since then I've changed the suspension to put the car to only 1" lower than stock.

When I get on my other computer I'll show a picture of the driveway hell I went through. My driveway has a steep slope down and to keep the water at the top the previous owner created a sharp crest up then down. Everything bar my 4-runner got high centred on it. So it took a 2 weekends of kanga hammering and rebar cutting to remove the crest to a plateau.

Ah, what we do for the love of our cars.

Psymon Mentor

Psymon

Posted
Posted

I've just moved into a place with a driveway that a standard commodore can scrape its front bar on! I haven't tried with the skyline yet because it's still off getting work done but i'm not looking forward to it :blush:

elysium Enthusiast

elysium

Posted
Posted

i havnt even bothered with my driveway, Its narrow, steep and short and isnt even from one side to the other. my mate in a vy commo tore his muffler off coming into it, his is lowered a little but nothing compared to my gtr. my gf suzuki swift scraps front on coming down it and they are a short car...

ill have to post a pic one of these days...

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)

I feel your pain.

Start on a 45 degree angle (pointed right), slowly bring it back to 45 degree left and slowly over the top rise.

I can have either my 2 dogs, or 1 passenger under 100kg in the passenger seat else I scrape exhaust tip on the bottom and the front pipe over rise (worse with 3" exhaust).

If I have a car load of people, they all get turfed at the bottom and have to walk up. 40C or 14C with hail = GTFO and walk up.

Part of the reason we are moving next week :)

Even my wife's Magna has been known to scrape and we had mates who were going to back their HiLux up, but couldn't clear the towball.

Edited by iamhe77
  • 11 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...