Jump to content
SAU Community

Recommended Posts

I am looking at the Mines & Reimax cam cover baffles for the RB26's. The thing I can quite get my head around is physically how large are they? Does anyone have some approx dimension - particularly for the Mines ones. The Reimax equivalents appear to be much shorter.

Both are shown on the Greenline site if anyone is wondering where to look.

Link to comment
https://www.sau.com.au/forums/topic/256610-cam-cover-baffles/
Share on other sites

I am looking at the Mines & Reimax cam cover baffles for the RB26's. The thing I can quite get my head around is physically how large are they? Does anyone have some approx dimension - particularly for the Mines ones. The Reimax equivalents appear to be much shorter.

Both are shown on the Greenline site if anyone is wondering where to look.

ive fitted 5 sets of these...the most recent on Sunday. The Mines ones are longer and need to be drilled to clear the cam cap studs if you keep the baffle caps on.

ive fitted 5 sets of these...the most recent on Sunday. The Mines ones are longer and need to be drilled to clear the cam cap studs if you keep the baffle caps on.

I never drilled mine !

Did you move the baffle caps to the new position as shown in the instructions ?

cheers cokey

I never drilled mine !

Did you move the baffle caps to the new position as shown in the instructions ?

cheers cokey

do you have camp cap studs? or just the std bolts?

i think paul was referring to the aftermarket studs having to be clearanced

do you have camp cap studs? or just the std bolts?

i think paul was referring to the aftermarket studs having to be clearanced

Just the std setup which are bolts for all but the 8 which hold the baffle caps they are studs.

Maybe Paul could post a pic of the drilling ?

When he has a minute,as he is busy preparing for new arrival.

Best wishes to stace.

cokey

Just the std setup which are bolts for all but the 8 which hold the baffle caps they are studs.

Maybe Paul could post a pic of the drilling ?

When he has a minute,as he is busy preparing for new arrival.

Best wishes to stace.

cokey

yeah the ones ive installed all used cam cap studs...not bolts...so needed drilling.

new arrival?

Edited by DiRTgarage
  • 2 weeks later...
  • 3 weeks later...

Anyone able to give a quick run-down of how to install these puppies? I picked up a set this week but came with no instructions (I know there are ones posted above, however I don't read Japanese) Is it a simple straight swap affair or do some modifications need to be performed?

  • 1 month later...

I'm wondering, would it be overkill to use both the Mines triple flow baffle plates, and a oil/air seperator at the same time?

I'm also wondering with the Mine's plates, oil purists here (not one myself, but hypothetically anyway); wouldn't you want the blowby oil that would normally come out the stock baffle plate to be caught by your oil catch can than a oil/air seperator or the triple flow baffle plates sending it back into the sump?

Anyone able to give a quick run-down of how to install these puppies? I picked up a set this week but came with no instructions (I know there are ones posted above, however I don't read Japanese) Is it a simple straight swap affair or do some modifications need to be performed?

Check attachment if still needed the instructions

Installation_Instructions_for_Triple_Flow_Cam_Cover_Baffle_Plate.pdf

  • Like 1

Take em out , blank the breathers off and use a GZ vacuum pump , helps seal the rings better - reduces blow by -reduced and relieves crank case pressure - allows oil to drain out of the head quicker at higher rpm and increases hp - up to 50hp in some cases.Also helps keep oil cleaner if running a little rich in some areas. Good bank for buck.

Take em out , blank the breathers off and use a GZ vacuum pump , helps seal the rings better - reduces blow by -reduced and relieves crank case pressure - allows oil to drain out of the head quicker at higher rpm and increases hp - up to 50hp in some cases.Also helps keep oil cleaner if running a little rich in some areas. Good bank for buck.

do you plumb the pump into the back welsh plug where you typically plumb the head drain into?

what kind of vacuum figure would you aim for in the crankcase?

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...