Jump to content
SAU Community

Recommended Posts

  • Replies 2k
  • Created
  • Last Reply

Top Posters In This Topic

']i have a DR30.

yeh the diagrams on FJ20.com are the 2 that are no good. its a 2 page diagram of the ECU wiring. i need the full wiring diagram with fuel pump etc on it.

OK,first thing you must have is a test light.If you had a burning smell first check all your fusible links(on mine there is 3 at the battery and 4 at the fuse box)

The fuse box (drivers side firewall) contains all your fuses and relays including your fuel pump relay.If all your fuses/fusible links are ok you should have power to all the relays and the fuel pump relay should click off after a few seconds with ignition on.If all is ok connect your test light to the fuel pump and with ignition on or engine cranking you should have power to the pump.

Try that and see where you end up.

Todd

Yeah I was thinking today that I want to be able to see the screen easily as I'll use the speedo function (will calibrate with a GPS) so I might put it on top of the steering column inside a tek box so it looks like a Jaycar digital speedo.

Does anyone know how that annoying 114kmh beeper works? Does it just get a signal from the ecu when the car exceeds 114, or does it recieve the speed signal?

Yeah I was thinking today that I want to be able to see the screen easily as I'll use the speedo function (will calibrate with a GPS) so I might put it on top of the steering column inside a tek box so it looks like a Jaycar digital speedo.

Does anyone know how that annoying 114kmh beeper works?  Does it just get a signal from the ecu when the car exceeds 114, or does it recieve the speed signal?

whats the device that makes the beeping noise?? is it standard or after market?

ADAM,I'm not sure if it runs off actual speed,or just an ecu output,as you say.At a guess,I'd say it runs off the speed sensor wire,the units in HR31's do....

What I am sure of,is if you want to compleatly remove the whole 'ding' module,and stick it in a postpack I'd be more than happy to shout you a couple of beers :rant: or send it $10 COD.... I WANT ONE!!!!!!

ADAM,I'm not sure if it runs off actual speed,or just an ecu output,as you say.At a guess,I'd say it runs off the speed sensor wire,the units in  HR31's do....

What I am sure of,is if you want to compleatly remove the whole 'ding' module,and stick it in a postpack I'd be more than happy to shout you a couple of beers :P or send it $10 COD.... I WANT ONE!!!!!!

I may have a spare one lying around, ill get back to you on that one

Yeah I was thinking today that I want to be able to see the screen easily as I'll use the speedo function (will calibrate with a GPS) so I might put it on top of the steering column inside a tek box so it looks like a Jaycar digital speedo.

Does anyone know how that annoying 114kmh beeper works?  Does it just get a signal from the ecu when the car exceeds 114, or does it recieve the speed signal?

My mate has an S13 180SX and he can't change the sensor, but the beeper itself simply attaches to the back of the speedo by 2 screws.

He removed the beeper/speaker and NO MORE NOISE, but you have to put the screws back, something to do with open circuits, as others have removed the beeper, left the screws out and had problems with the speedo fluctuating.

well i went outside today to my car to pull the dash apart and look for any burnt wires but decided before doing that id open the fuse box and turn ignition and listen for any of the relays ticking over to try and find fuel pump relay.

anyway, turned the key and *bzzzt* pump was back to life. power was back to it again. i then turned it on and it was super lumpy and rough. checked the pressure guage and it was reading 41psi idle pressure rather than the 34psi i set it to the day before before it died. then found out that the guage, rather than sitting on zero, was actually sitting another 1/4 of the guage face further down, below the vacuum area (guage had vacuum bit on the bottom 1/4 of it). so it was probably about 15psi out or so :P so wen i connected it initially and thought it was at 19psi, it was probably at 34psi like i wanted. and then wen i turned it up to 34psi, it was more like 50psi idle pressure. so wen i took it for the 2 spins round the block, it must have just overloaded the system and thats y the wires were burning. ECU must have noticed and cut the power to the pump at this point i guess.

so i connected another guage, disconnected the 2nd air valve thing that i had hooked up yesterday when it was at the wrong higher pressure, and got some new plugs since the old ones were all fouled up, and it sat and idled perfectly at 34psi idle pressure.

so just gota take it for a drive tomorow and see how it goes, see if it still has the huge misfire that it had and if it starts to get too hot and short the wires again. hopefully no permanent damage was done but we'll see tomorow i guess!

Its located underneath where the head unit goes in the '30s I think.  If it gets a feed from the speed sensor wire then that would be quite useful

Its to the right of the cig lighter, those three lines/slots in the plastic allow the noise to come through, is a little metal box behind the slots.

Oh tell u what got a surprise the other night, opened the fridge to get some mayo out and the bottle behind it had a familiar face on it!

It was baltic or balsamic vinegar and it was Paul Newmans own brand!!!

sorry totally off topic and random, just surprised me and Ghostriders signature trigger me

was driving home this morning from a mates place and saw an all black hr30 2door driving the other way, big ass fmic taking up the whole front centre, sounded rotoraryish big on lumpy noise, turned around to try to flag him down but lost him?? so looks like these another 2door r30 on the coast, about bloody time...just have to track him down...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
    • Fair enough, I am in no way a tire expert so I'm not familiar with all the terms and conditions. I'll definitely note down the AD09 to potentially try in the future. Rain is not too big of a concern for now as I will probably only drive in the rain when I have to. And considering I still lack experience driving the GTR I'd more than likely take it easy too. I have coilovers in the car but as I barely got to drive so far I never bothered to even check if they are adjustable haha. The suspension is almost entirely old and worn as well so I suppose when I eventually fix that in the future that would make a huge difference.
×
×
  • Create New...