Jump to content
SAU Community

Recommended Posts

guys has anyone got any idea what this ticking noise could be coming from my car? (other than a bomb)

it only happens sometimes... like tonight i filled up at the servo... took off... went to do a u turn and gave it a bit of stick round the corner... went to the lights and it started ticking! sounded like a metal ticking noise... quite loud.

then when i got home and went to check it out it stopped... well it stopped b4 i got home...

its happend a few times recently... seems to be after i give it a bit of a caining... but then again i took it around the rds just then and thrashed it and nothing... sounds normal.

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/
Share on other sites

If its a turbo gasket you'll here it eminating from around the turbo (obviously), and it'll gradually get worse.

Thats what mine did.

When it starts ticking again, get someone to rev it and stick your head near the turbo and have a good listen.

Though my noise didn't come and go as yours does?

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-551859
Share on other sites

cool... hasnt done it for ages... oil is fine theres no leaks anywhere from what i can see... but eric ur suggestion sounds like it could have some merit as it did end up going away once the car was warmed up properly... mind u it hasnt happend since i posted this :)

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-551964
Share on other sites

Originally posted by pushead

the noise comes on right behind the dash right? like a clinging ticking noise but after the car is warmed up properly its ok .

yeah i get that too

its like a creaking sound but once the engine is warm it goes away

what is that?

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-557001
Share on other sites

I also get this ticking noise when I first start the car up from cold. Idles for about a minute then goes away...dosen't sound nice when it does it though...

It's not the lifters or injectors, very loud and distinct, and only happens when I start it in the morning.

I have read a few other forums and could it be the oil pump not working properly when it's cold?

I think we all would be GREATLY appreciative if someone knows what is happening...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-560394
Share on other sites

I had a decent listen this morning (sat) and I think it sounds like the lifters or something in that part of the engine, because it stills make noise after its started, so possible not the starter motor or something....I have no idea really, take it to the experts when I can...

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-565133
Share on other sites

  • 3 weeks later...

just to let anyone know still interested in this, I haven't been able to get to Ice Performance yet, but I found out (I think) why my engine was making a ticking noise; I was parking on a lean and the oil must of drained almost completely out of one side of the head and thus when I started it in the morning there was no oil there to lube up the cam and lifters, etc. until the pump got the oil up there. Have been parking on level ground since and not one ticking noise!!

hoorah!

Link to comment
https://www.sau.com.au/forums/topic/25977-ticking-noise/#findComment-587603
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...