Jump to content
SAU Community

Recommended Posts

hay just a quick one for you all....

i had this with my r32 as well (4wd). everytime i change the oil filter, it doesn't matter what i put under there or what i lose heaps of oil from it and it leaks all over the stuff below it and its really starting to shit me...

what do you guys do to not lose sooo much oil?

Thanks

curt

Link to comment
https://www.sau.com.au/forums/topic/259774-oil-change-question/
Share on other sites

even with a relocator kit - it can still be messy (I have a relocator in mine)...makes it eaiser to get the filter on and off...I always have a rag on standby for spillage as there is still some oil in the relocator

Here are a couple of photos of my oil cooler and relocation kit. Oil cooler on the driver’s side. Auto cooler on the passenger side

post-25786-1236238450_thumb.jpg

I found a couple of welded nuts in the chassis rail under the driver’s feet (aprox) and made up a bracket to suit for the filter

post-25786-1236238240_thumb.jpg

sounds to me like you've still got a rubber seal from an old filter on the block - the rubber o-rings can be left behind when you remove a filter so make sure that you take it off if it didn't come off with the filter. if you've still got an old o-ring on (without knowing) and have put a new filter on with its own o-ring then this will more than likely cause a leak. i'd check this before wasting money on a relocator at this point - it's not like the filter on them is exactly hard to get to..

oops kinda missread the original post :P

there will always be a little oil left in the filter even if you've drained the sump but not enough to worry about?

to answer the q about oil coolers:

they're fine for everyday use but be careful you don't run your oil too cool. ie if it's just a daily and you live in a colder climate i'd advise against it as the oil needs to heat up to thin out and work properly. a few of the guys i know that run oil coolers on daily drivers put bags over them in the colder months of the year to prevent air flow through it and then take them off when it heats up :laugh:

I did this yesterday arvo.

Have a greddy oil relocator kit so that it sits up above the fuel filter

Have a fujimoto oil drain release valve, so that its just a flick to release oil then flick back to shut off

Released the oil into old container - only 3750ml WTF?!

changed oil filter, changed spark plugs, then ran on only 5cyl so redid sparkies

filled with 5L Motol 3100V, then reset ecu

test drove revealed issue, redid as above all is great and ready for dyno run next week !

not using an oil cooler myself, just an Automatic gearbox-oil cooler

Yup i agree with what the guys said above, Drain the sump first & give it a fair bit of time before taking the filter off. I only witnessed a few drops from taking off the filter, from all the times i've done it.

Just have a rag handy :P

Undo filter a little, enough so it's not tight, get a plastic bag, cover entire filter with bag, undo the rest of the filter through the bag. Hopefully most of the oil left over in filter ends up in bag. Oh, and also a rag under the filter for good measure.

leave the filler cap or a breather hose off while draining oil, walk away for atleast ten mins before considering doing the filter(this is when i do my plugs) then change filter, fit sump plug and new washer(AW12), fill with oil

Undo filter a little, enough so it's not tight, get a plastic bag, cover entire filter with bag, undo the rest of the filter through the bag. Hopefully most of the oil left over in filter ends up in bag. Oh, and also a rag under the filter for good measure.

Huh? Why not use a drip tray?

Preferably one with a nozzle so you can pour used oil into the container that the new oil came in.

Agree with RBPOWA, drip tray under drain plug, release oil from sump, when finished draining re-position drip ray under oil filter, remove filter and drain into drip tray.

No mess, no fuss :banana:

Huh? Why not use a drip tray?

Preferably one with a nozzle so you can pour used oil into the container that the new oil came in.

Agree with RBPOWA, drip tray under drain plug, release oil from sump, when finished draining re-position drip ray under oil filter, remove filter and drain into drip tray.

No mess, no fuss :banana:

he means over the filter to catch those little drops that make ur engin bay look dirty... how much are oil filter relocation kits? the 260s is soooo much harder!

has any one used those new DRIFT filters? apparently they have a bolt on the back of them so if its too tight get a socket onto it and ur set!

Edited by chef_stagea
has any one used those new DRIFT filters? apparently they have a bolt on the back of them so if its too tight get a socket onto it and ur set!

So do the K&N oil filters, for about the same price.... and much higher quality (or so I am told by a mate who sells both)

yeah I usually do it as you both have described- but I think if your filter has an anti drainback valve this causes problems too - you will get a bit of spillage but not a massive amt

as above says XD drain the sump for good 10 mins :D then take filter off( a little bit will dribble ) then new filter sump washer and wash down sump and filter area new oil off you go :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...