Jump to content
SAU Community

Removed My Rocker Covers To Find This!

DaveO74

By DaveO74,
in Engines & Forced Induction

 Share

Recommended Posts

DaveO74 Mentor

DaveO74

Posted
Posted

Hey Guys,

While Im waiting for my High-Flow to turn up I thought I would finish some engine painting that I started long ago so I removed my Rocker Covers. When I got them off and was having a good look at them before cleaning and paint prep i found on the underside of the cover on the Intake side near the rear of the engine (Firewall) this burnt oils stain type marking. (See photo below)

Should I worry about this stain or is it just something that comes with age??

Also what is the best way to remove the copper coloured blow by hose thingys on top if each cover?(Very technical I know)

Thanks

post-31195-1236507642_thumb.jpg

gotRICE? Veteran

gotRICE?

Posted
Posted
The rocker cover breather fittings are simply pressed in. Just get a screwdriver in the opening and twist it back and forwards while you pull it up.

:D I tried that when i did mine, thos suckers are in tight! (well you'd hope so :)) I gave up and masked them. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...