Jump to content
SAU Community

Recommended Posts

Gibson R31 and Gibson R32 on track with no other traffic (well, there was an R35 somewhere in the mix) to muffle their sounds.

What a fantastic day of spectating.

Once again Boz, thanks for starting the thread, much appreciated :(

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Is this Dave Nolan??

18's is fast for a standard full weight road car . I would like to see what your standard civic does haha

The GTR did a 2min24 around Bathurst in standard trim. It could actually stretch its legs up there. The fastest IPRA is a 2min28 LOL

a guy i work with was telling me about this on tuesday.

his name is Brett, do you remember talking to him also John ? he said his brother owns the r32 , i just dont know his surename, so it could be Ashwood for all i know, i'll double check tomorrow at work

  • 2 years later...

Does anyone know who won in lap times the winfield gtr or the R35 GTR, I cant beleive no one has asked this? ANd what the hell does 18,s mean or 17s mean. Cant a simple best lap time for the winfield gtr and a simple lap time for the r35 gtr be posted up?

Well doing some research On the bathurst track i seen that 2:12min was the record for a R32 GTR back in 91/92 I think i saw tat a stock R35 did it in 2.25min.

records for v8s are:

The lap record for the race is the 2:08.4651 recorded by Jamie Whincup in his Ford BF Falcon in 2007,[1] not to be confused with the fastest lap ever recorded, a 2:06.8012 set during practice in 2010 by Holden driver Craig Lowndes.[2]

But i wonder with all the new technology now modding an r32 GTR would even challenge todays v8 Supercars.. AMAZING

Edited by GTRAAH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...